KENWOOD KA-4002 Solid State Stero Amplifier Service Manual Original GenuineSKU: SB-01586 ____________________________________________________Please Note:All service manuals are original and so: Have sharp clear text and diagrams Often have large pull-out circuit diagrams Will have some wear and tear and possible written comments May have rusty staples Are not low quality re-prints from the internet.

Kenwood KA-4002 Verstärker Ein Kanal geht nicht Auf Kopfhörer gehen beide Zustand siehe Fotos Verkauf als defekt

Kenwood KA-4002 Verstärker Ein Kanal geht nicht Auf Kopfhörer gehen beide Zustand siehe Fotos Verkauf als defekt

Amplificateur vintage KENWOOD KA4002 , 6 entrées sources dont 2 phonos , cette ampli donne une merveilleuse sonorité typé bien quil est a transistors , la puissance sur le papier le donne pour 2x18watts , mais il est impossible de le mettrele volume a fond tellement on lentend ,ce modèle au départ été prévu avec les joues en bois que je nest pas , il est presque dorigine jai changer les 2 condensateurs chimiques et jai mis des borniers haut parleur a fiche banane pour un meilleur commodité pour brancher du cable hp de plus grosse section , lampli fonctionne bien. Power output: 18 watts per channel into 8? (stereo) Frequency response: 20Hz to 40kHz Total harmonic distortion: 0.5% Damping factor: 50 Input sensitivity: 2.5mV (MM), 150mV (line) Signal to noise ratio: 60dB (MM), 70dB (line) Output: 150mV (line), 30mV (DIN) Speaker load impedance: 4? to 16? Semiconductors: 18 x transistors, 10 x diodes Dimensions: 13 x 4-5/8 x 9-7/16 inches Weight: 5.7kg

KENWOOD KA-4002 Lässt sich einschalten weitere Funktion nicht möglich kein ton :::

Ampli Kenwood Vintage KA-4002A. Superbe tat dorigine, les potentiomtres sont propres et ne craquent pas. Superbe fabrication, superbe son, belle tessiture, ar, enveloppant.... La led rouge ne sallume pas, mais lampli fonctionne parfaitement. Peut tre quelle ne sallume quen mode recording ? The Kenwood KA-4002 is the solid state stereo amplifier that packs a compact sized wallop. With 58 watts and intensely low distortion, this instrument guarantees top level performance of the highest proportions. Another remarkable example of Kenwoods complete, high quality circuitry, the KA-4002 also stresses modern, up to date design with its simple stylized exterior. Its unbeatable craftsmanship makes this model another testimony to Kenwoods deserved world fame. Specifications 4002 4002A Power output: 18 watts per channel into 8 (stereo) Frequency response: 20Hz to 40kHz Total harmonic distortion: 0.5% Damping factor: 50 Input sensitivity: 2.5mV (MM), 150mV (line) Signal to noise ratio: 60dB (MM), 70dB (line) Output: 150mV (line), 30mV (DIN) Speaker load impedance: 4 to 16 Semiconductors: 18 x transistors, 10 x diodes Dimensions: 13 x 4-5/8 x 9-7/16 inches Weight: 5.7kg

Used Kenwood KA 2002 Solid State Integrated amplifier is in great working condition. All control knots function as its should product a warm tube-like sound in all kind of music. Stereo 13 watts per channel into 8 ohm sound like 40 watts. Dimension : 330X115X240mmweight 4.8kg made this beautiful compact up to date design with its simple stylized exterior its unbeatable craftsmanship makes this model testimony to Kenwoods deserved world fame.

Unit turns on and operates, with static on one channel when last hooked up to a system. The unit has had the pots and switches worked with deoxit. Has a nice wood case that has been treated with restore finish but has minor defects on finished surfaces and a large gouge in the bottom particle board base. It also has one foot that has been replaced and is not the same length as the others. May be something simple to make it 100% but I have not done any diagnostics on the unit.and its very intermittent on its operation. No returns accepted due to parts swapping.

Unit turns on and operates, with static on one channel when last hooked up to a system. The unit has had the pots and switches worked with deoxit. Has a nice wood case that has been treated with restore finish but has minor defects on finished surfaces and a large gouge in the bottom particle board base. It also has one foot that has been replaced and is not the same length as the others. May be something simple to make it 100% but I have not done any diagnostics on the unit.and its very intermittent on its operation. No returns accepted due to parts swapping.