FRoom

Bob Carvers design and engineering Low distortion the doesnt go up with volume, few makers achieved this Bob was pioneer in short no wire connection that resulted in awesome sound and music recreation or original recordings. I like Adcom and Onyko amps, but Carver out did all competition in its price range. This retailed around 500 and still holds that value as parts needed to keep working great are readily available on Ebay. Amp has scratches and marks throughout as this has been around about 40 years. Powers up and pounds as it should has on off switch on front ( some Carvers do not have front power switch). Priced to sell and enjoy, may need recaps sometime in the future as all vintage amps do to keep sound clean and distortion free. Working great as of last use. Wont disappoint. I have never open it up. No need so far. Listed below market value to sell. 200 WPC at 8 ohm loads.

Great condition and works great.

Carver M-1.0T Magnetic Field Power Amplifier, Beautiful Condition. Purchased it about 2 years ago. Used it as my main audio amp for about a year. I love it and hate to part with it, but re configured our living space and I have no more room for a large system. That is the only reason for the sale.

Carver M-1.0T Magnetic Field Power Amplifier, Amazing Condition. Condition is Used. Shipped with USPS Ground Advantage.

SN#07158 Unit powers on, does not blow fuses, bottom row of LEDs light up. Right channel has 11.5 VDC on output, left channel puts out slight buzz on speaker. Looks all original. Black casing is scrathed up, silver faceplate looks pretty good.

Carver M-1.0t mk II specifications Stock Mk II opt 002 Power 8 ohms 200 watts <0.15% THD 400 watts <0.15% THD 460 watts < 0.15% THD 4 ohms 400 watts <0.15% THD 450 watts <0.15% THD 510 watts < 0.15% THD At Clipping 8 ohms 350 watts 450 watts 500 watts 4 ohms 500 watts 520 watts 555 watts Dynamic 8 ohms 550 watts 670 watts 700 watts 4 ohms 832 watts 940 watts 1000 watts 2 ohms 928 watts 1250 watts 1290 watts New FulcrumTM bias pivot The original bias network (black) allows the bias point to drift as temperature increases. Addition of a complimentary transistor and network counteracts this drift, and maintains the bias set point. As a result, heatsink temperatures are reduced by 10 degrees F. M-1.0t MARK II Manual Addendum The M-1.0t is one of the most under-rated amplifiers of all time. Its rumored that this was done to fit the m-1.0t in the model line (0.5, 1.0, 1.5 and 4.0). Its also suggested that it was rated at 200W to match the Conrad Johnson Premier V rating (the $12,000 tube amplifier it was transfer function modified to sound like).Features:· *All new electrolytic capacitors replaced and upgraded, including new High Voltage, Long Life *power supply capacitors· *All pre-driver stage transistors replaced and upgraded· *All rectifiers replaced and upgraded· *All Main switching Diodes replaced· *Trouble resistors replaced and upgraded where needed· *Output transistor parallel doubled for high current handling (opt002 only)· *High current output commutators installed (opt002 only)· *Bias Pivot upgrade· *On/Off Thump Fix circuits installed· *Solder joints reflowed and inspected.· *Premium Quality 7% silver solder used on output stage· *5-way gold speaker binding posts · *Unit cleaned inside and out

Carver M-1.0t mk II specifications Stock Mk II opt 002 Power 8 ohms 200 watts <0.15% THD 400 watts <0.15% THD 460 watts < 0.15% THD 4 ohms 400 watts <0.15% THD 450 watts <0.15% THD 510 watts < 0.15% THD At Clipping 8 ohms 350 watts 450 watts 500 watts 4 ohms 500 watts 520 watts 555 watts Dynamic 8 ohms 550 watts 670 watts 700 watts 4 ohms 832 watts 940 watts 1000 watts 2 ohms 928 watts 1250 watts 1290 watts New FulcrumTM bias pivot The original bias network (black) allows the bias point to drift as temperature increases. Addition of a complimentary transistor and network counteracts this drift, and maintains the bias set point. As a result, heatsink temperatures are reduced by 10 degrees F. M-1.0t MARK II Manual Addendum The M-1.0t is one of the most under-rated amplifiers of all time. Its rumored that this was done to fit the m-1.0t in the model line (0.5, 1.0, 1.5 and 4.0). Its also suggested that it was rated at 200W to match the Conrad Johnson Premier V rating (the $12,000 tube amplifier it was transfer function modified to sound like).Features:· *All new electrolytic capacitors replaced and upgraded, including new High Voltage, Long Life *power supply capacitors· *All pre-driver stage transistors replaced and upgraded· *All rectifiers replaced and upgraded· *All Main switching Diodes replaced· *Trouble resistors replaced and upgraded where needed· *Output transistor parallel doubled for high current handling (opt002 only)· *High current output commutators installed (opt002 only)· *Bias Pivot upgrade· *On/Off Thump Fix circuits installed· *Solder joints reflowed and inspected.· *Premium Quality 7% silver solder used on output stage· *5-way gold speaker binding posts · *Unit cleaned inside and out

Genuine Carver M-1.0T Magnetic Field Power Amplifier . Tested in working condition

Genuine Carver M-1.0T Magnetic Field Power Amplifier . Tested in working condition

Genuine Carver M-1.0T Magnetic Field Power Amplifier . Tested in working condition