Description Design The CXPP series was designed as a high quality output transformers push-pull tube amplifiers. Primary (Input) The input is designed for a 10K Ohms impedance source. Screen/Grid Tap This unit has a 40% screen/grid. Secondary (Output) The output impedance is designed for speakers. Magnet Wire All units are wound with the finest virgin copper magnet wire. All windings use heavy insulated wire to provide excellent manufacturing yield, lower customer cost and superior life. The Core EDCOR uses the finest M6 line grain oriented steel cores. Each unit is hand stacked to assure at least 92% stack. The Bobbin Injection molded Nylon 6/6 with the addition of 30%-35% glass fibers. The addition of glass fibers allows a higher heat deflection temperature and it brings the material to a class HB UL temperature classification. Termination The terminations are UL1015 20 ga. color coded lead wire around 15 inches (38cm) long. Mounting This unit comes with steel end bells for mounting with the use of four screws. See dimensional drawing. Specifications Wattage 30W Primary (input) Impedance 10K ? Screen/Grid Tap 40% Secondary (output) Impedance Depends on model. Winding Configuration Interleave Winding Frequency Response 20~20K Hz., <1dBu THD+Noise <0.1% @ 1K Hz. Insertion Loss <1 dB Bobbin Material Nylon 6/6 GF-30 Flammability Rating Class HB Coil Finish Wrapping Polyester Film Electrical Insulating Tape Core Size EI125 (1.25 x 1.5) Core Material M-6 29 ga. grain oriented lamination steel Secondary Insulation Clear air dry polyester varnish Termination 15 (38cm) UL1015, 20 ga. lead wire Mounting Steel end bell covers Mounting Orientation Vertical Weight 6 lbs.

Description Design The CXPP series was designed as a high quality output transformers push-pull tube amplifiers. Primary (Input) The input is designed for a 10K Ohms impedance source. Screen/Grid Tap This unit has a 40% screen/grid. Secondary (Output) The output impedance is designed for speakers. Magnet Wire All units are wound with the finest virgin copper magnet wire. All windings use heavy insulated wire to provide excellent manufacturing yield, lower customer cost and superior life. The Core EDCOR uses the finest M6 line grain oriented steel cores. Each unit is hand stacked to assure at least 92% stack. The Bobbin Injection molded Nylon 6/6 with the addition of 30%-35% glass fibers. The addition of glass fibers allows a higher heat deflection temperature and it brings the material to a class HB UL temperature classification. Termination The terminations are UL1015 20 ga. color coded lead wire around 15 inches (38cm) long. Mounting This unit comes with steel end bells for mounting with the use of four screws. See dimensional drawing. Specifications Wattage 30W Primary (input) Impedance 10K ? Screen/Grid Tap 40% Secondary (output) Impedance Depends on model. Winding Configuration Interleave Winding Frequency Response 20~20K Hz., <1dBu THD+Noise <0.1% @ 1K Hz. Insertion Loss <1 dB Bobbin Material Nylon 6/6 GF-30 Flammability Rating Class HB Coil Finish Wrapping Polyester Film Electrical Insulating Tape Core Size EI125 (1.25 x 1.5) Core Material M-6 29 ga. grain oriented lamination steel Secondary Insulation Clear air dry polyester varnish Termination 15 (38cm) UL1015, 20 ga. lead wire Mounting Steel end bell covers Mounting Orientation Vertical Weight 6 lbs.

Description Design The CXPP series was designed as a high quality output transformers push-pull tube amplifiers. Primary (Input) The input is designed for a 10K Ohms impedance source. Screen/Grid Tap This unit has a 40% screen/grid. Secondary (Output) The output impedance is designed for speakers. Magnet Wire All units are wound with the finest virgin copper magnet wire. All windings use heavy insulated wire to provide excellent manufacturing yield, lower customer cost and superior life. The Core EDCOR uses the finest M6 line grain oriented steel cores. Each unit is hand stacked to assure at least 92% stack. The Bobbin Injection molded Nylon 6/6 with the addition of 30%-35% glass fibers. The addition of glass fibers allows a higher heat deflection temperature and it brings the material to a class HB UL temperature classification. Termination The terminations are UL1015 20 ga. color coded lead wire around 15 inches (38cm) long. Mounting This unit comes with steel end bells for mounting with the use of four screws. See dimensional drawing. Specifications Wattage 30W Primary (input) Impedance 10K ? Screen/Grid Tap 40% Secondary (output) Impedance Depends on model. Winding Configuration Interleave Winding Frequency Response 20~20K Hz., <1dBu THD+Noise <0.1% @ 1K Hz. Insertion Loss <1 dB Bobbin Material Nylon 6/6 GF-30 Flammability Rating Class HB Coil Finish Wrapping Polyester Film Electrical Insulating Tape Core Size EI125 (1.25 x 1.5) Core Material M-6 29 ga. grain oriented lamination steel Secondary Insulation Clear air dry polyester varnish Termination 15 (38cm) UL1015, 20 ga. lead wire Mounting Steel end bell covers Mounting Orientation Vertical Weight 6 lbs.

Zwei original Experience-Electronics Ausgangsübertrager.High End Übertrager für 4x EL 84 Röhren im Ultralienearbetrieb. Maximal übertragbare Leistung: > 30 WFrequenzgang : 20hz bis 20KhzSekundärausgänge: 2,4,8 Ohm. Die Trafos waren nur wenig im Einsatz, und wurden 2004 ausgebaut und eingelagert.Eine Funktionsprüfung ist leider nicht möglich, daher werden die Trafos ohne Garantie und Gewährleistung verkauft. Der Verkaufspreis bezieht sich auf beide Trafos. (Paarpreis)

Description Design The CXPP series was designed as a high quality output transformers push-pull tube amplifiers. Primary (Input) The input is designed for a 10K Ohms impedance source. Screen/Grid Tap This unit has a 40% screen/grid. Secondary (Output) The output impedance is designed for speakers. Magnet Wire All units are wound with the finest virgin copper magnet wire. All windings use heavy insulated wire to provide excellent manufacturing yield, lower customer cost and superior life. The Core EDCOR uses the finest M6 line grain oriented steel cores. Each unit is hand stacked to assure at least 92% stack. The Bobbin Injection molded Nylon 6/6 with the addition of 30%-35% glass fibers. The addition of glass fibers allows a higher heat deflection temperature and it brings the material to a class HB UL temperature classification. Termination The terminations are UL1015 20 ga. color coded lead wire around 15 inches (38cm) long. Mounting This unit comes with steel end bells for mounting with the use of four screws. See dimensional drawing. Specifications Wattage 30W Primary (input) Impedance 10K ? Screen/Grid Tap 40% Secondary (output) Impedance Depends on model. Winding Configuration Interleave Winding Frequency Response 20~20K Hz., <1dBu THD+Noise <0.1% @ 1K Hz. Insertion Loss <1 dB Bobbin Material Nylon 6/6 GF-30 Flammability Rating Class HB Coil Finish Wrapping Polyester Film Electrical Insulating Tape Core Size EI125 (1.25 x 1.5) Core Material M-6 29 ga. grain oriented lamination steel Secondary Insulation Clear air dry polyester varnish Termination 15 (38cm) UL1015, 20 ga. lead wire Mounting Steel end bell covers Mounting Orientation Vertical Weight 6 lbs.

Description Design The CXPP series was designed as a high quality output transformers push-pull tube amplifiers. Primary (Input) The input is designed for a 10K Ohms impedance source. Screen/Grid Tap This unit has a 40% screen/grid. Secondary (Output) The output impedance is designed for speakers. Magnet Wire All units are wound with the finest virgin copper magnet wire. All windings use heavy insulated wire to provide excellent manufacturing yield, lower customer cost and superior life. The Core EDCOR uses the finest M6 line grain oriented steel cores. Each unit is hand stacked to assure at least 92% stack. The Bobbin Injection molded Nylon 6/6 with the addition of 30%-35% glass fibers. The addition of glass fibers allows a higher heat deflection temperature and it brings the material to a class HB UL temperature classification. Termination The terminations are UL1015 20 ga. color coded lead wire around 15 inches (38cm) long. Mounting This unit comes with steel end bells for mounting with the use of four screws. See dimensional drawing. Specifications Wattage 30W Primary (input) Impedance 10K ? Screen/Grid Tap 40% Secondary (output) Impedance Depends on model. Winding Configuration Interleave Winding Frequency Response 20~20K Hz., <1dBu THD+Noise <0.1% @ 1K Hz. Insertion Loss <1 dB Bobbin Material Nylon 6/6 GF-30 Flammability Rating Class HB Coil Finish Wrapping Polyester Film Electrical Insulating Tape Core Size EI125 (1.25 x 1.5) Core Material M-6 29 ga. grain oriented lamination steel Secondary Insulation Clear air dry polyester varnish Termination 15 (38cm) UL1015, 20 ga. lead wire Mounting Steel end bell covers Mounting Orientation Vertical Weight 6 lbs.

Description Design The CXPP series was designed as a high quality output transformers push-pull tube amplifiers. Primary (Input) The input is designed for a 10K Ohms impedance source. Screen/Grid Tap This unit has a 40% screen/grid. Secondary (Output) The output impedance is designed for speakers. Magnet Wire All units are wound with the finest virgin copper magnet wire. All windings use heavy insulated wire to provide excellent manufacturing yield, lower customer cost and superior life. The Core EDCOR uses the finest M6 line grain oriented steel cores. Each unit is hand stacked to assure at least 92% stack. The Bobbin Injection molded Nylon 6/6 with the addition of 30%-35% glass fibers. The addition of glass fibers allows a higher heat deflection temperature and it brings the material to a class HB UL temperature classification. Termination The terminations are UL1015 20 ga. color coded lead wire around 15 inches (38cm) long. Mounting This unit comes with steel end bells for mounting with the use of four screws. See dimensional drawing. Specifications Wattage 30W Primary (input) Impedance 10K ? Screen/Grid Tap 40% Secondary (output) Impedance Depends on model. Winding Configuration Interleave Winding Frequency Response 20~20K Hz., <1dBu THD+Noise <0.1% @ 1K Hz. Insertion Loss <1 dB Bobbin Material Nylon 6/6 GF-30 Flammability Rating Class HB Coil Finish Wrapping Polyester Film Electrical Insulating Tape Core Size EI125 (1.25 x 1.5) Core Material M-6 29 ga. grain oriented lamination steel Secondary Insulation Clear air dry polyester varnish Termination 15 (38cm) UL1015, 20 ga. lead wire Mounting Steel end bell covers Mounting Orientation Vertical Weight 6 lbs.

Description Design The CXPP series was designed as a high quality output transformers push-pull tube amplifiers. Primary (Input) The input is designed for a 10K Ohms impedance source. Screen/Grid Tap This unit has a 40% screen/grid. Secondary (Output) The output impedance is designed for speakers. Magnet Wire All units are wound with the finest virgin copper magnet wire. All windings use heavy insulated wire to provide excellent manufacturing yield, lower customer cost and superior life. The Core EDCOR uses the finest M6 line grain oriented steel cores. Each unit is hand stacked to assure at least 92% stack. The Bobbin Injection molded Nylon 6/6 with the addition of 30%-35% glass fibers. The addition of glass fibers allows a higher heat deflection temperature and it brings the material to a class HB UL temperature classification. Termination The terminations are UL1015 20 ga. color coded lead wire around 15 inches (38cm) long. Mounting This unit comes with steel end bells for mounting with the use of four screws. See dimensional drawing. Specifications Wattage 30W Primary (input) Impedance 10K ? Screen/Grid Tap 40% Secondary (output) Impedance Depends on model. Winding Configuration Interleave Winding Frequency Response 20~20K Hz., <1dBu THD+Noise <0.1% @ 1K Hz. Insertion Loss <1 dB Bobbin Material Nylon 6/6 GF-30 Flammability Rating Class HB Coil Finish Wrapping Polyester Film Electrical Insulating Tape Core Size EI125 (1.25 x 1.5) Core Material M-6 29 ga. grain oriented lamination steel Secondary Insulation Clear air dry polyester varnish Termination 15 (38cm) UL1015, 20 ga. lead wire Mounting Steel end bell covers Mounting Orientation Vertical Weight 6 lbs.

Description Design The CXPP series was designed as a high quality output transformers push-pull tube amplifiers. Primary (Input) The input is designed for a 10K Ohms impedance source. Screen/Grid Tap This unit has a 40% screen/grid. Secondary (Output) The output impedance is designed for speakers. Magnet Wire All units are wound with the finest virgin copper magnet wire. All windings use heavy insulated wire to provide excellent manufacturing yield, lower customer cost and superior life. The Core EDCOR uses the finest M6 line grain oriented steel cores. Each unit is hand stacked to assure at least 92% stack. The Bobbin Injection molded Nylon 6/6 with the addition of 30%-35% glass fibers. The addition of glass fibers allows a higher heat deflection temperature and it brings the material to a class HB UL temperature classification. Termination The terminations are UL1015 20 ga. color coded lead wire around 15 inches (38cm) long. Mounting This unit comes with steel end bells for mounting with the use of four screws. See dimensional drawing. Specifications Wattage 30W Primary (input) Impedance 10K ? Screen/Grid Tap 40% Secondary (output) Impedance Depends on model. Winding Configuration Interleave Winding Frequency Response 20~20K Hz., <1dBu THD+Noise <0.1% @ 1K Hz. Insertion Loss <1 dB Bobbin Material Nylon 6/6 GF-30 Flammability Rating Class HB Coil Finish Wrapping Polyester Film Electrical Insulating Tape Core Size EI125 (1.25 x 1.5) Core Material M-6 29 ga. grain oriented lamination steel Secondary Insulation Clear air dry polyester varnish Termination 15 (38cm) UL1015, 20 ga. lead wire Mounting Steel end bell covers Mounting Orientation Vertical Weight 6 lbs.

Description Design The CXPP series was designed as a high quality output transformers push-pull tube amplifiers. Primary (Input) The input is designed for a 10K Ohms impedance source. Screen/Grid Tap This unit has a 40% screen/grid. Secondary (Output) The output impedance is designed for speakers. Magnet Wire All units are wound with the finest virgin copper magnet wire. All windings use heavy insulated wire to provide excellent manufacturing yield, lower customer cost and superior life. The Core EDCOR uses the finest M6 line grain oriented steel cores. Each unit is hand stacked to assure at least 92% stack. The Bobbin Injection molded Nylon 6/6 with the addition of 30%-35% glass fibers. The addition of glass fibers allows a higher heat deflection temperature and it brings the material to a class HB UL temperature classification. Termination The terminations are UL1015 20 ga. color coded lead wire around 15 inches (38cm) long. Mounting This unit comes with steel end bells for mounting with the use of four screws. See dimensional drawing. Specifications Wattage 30W Primary (input) Impedance 10K ? Screen/Grid Tap 40% Secondary (output) Impedance Depends on model. Winding Configuration Interleave Winding Frequency Response 20~20K Hz., <1dBu THD+Noise <0.1% @ 1K Hz. Insertion Loss <1 dB Bobbin Material Nylon 6/6 GF-30 Flammability Rating Class HB Coil Finish Wrapping Polyester Film Electrical Insulating Tape Core Size EI125 (1.25 x 1.5) Core Material M-6 29 ga. grain oriented lamination steel Secondary Insulation Clear air dry polyester varnish Termination 15 (38cm) UL1015, 20 ga. lead wire Mounting Steel end bell covers Mounting Orientation Vertical Weight 6 lbs.

Description Design The CXPP series was designed as a high quality output transformers push-pull tube amplifiers. Primary (Input) The input is designed for a 10K Ohms impedance source. Screen/Grid Tap This unit has a 40% screen/grid. Secondary (Output) The output impedance is designed for speakers. Magnet Wire All units are wound with the finest virgin copper magnet wire. All windings use heavy insulated wire to provide excellent manufacturing yield, lower customer cost and superior life. The Core EDCOR uses the finest M6 line grain oriented steel cores. Each unit is hand stacked to assure at least 92% stack. The Bobbin Injection molded Nylon 6/6 with the addition of 30%-35% glass fibers. The addition of glass fibers allows a higher heat deflection temperature and it brings the material to a class HB UL temperature classification. Termination The terminations are UL1015 20 ga. color coded lead wire around 15 inches (38cm) long. Mounting This unit comes with steel end bells for mounting with the use of four screws. See dimensional drawing. Specifications Wattage 30W Primary (input) Impedance 10K ? Screen/Grid Tap 40% Secondary (output) Impedance Depends on model. Winding Configuration Interleave Winding Frequency Response 20~20K Hz., <1dBu THD+Noise <0.1% @ 1K Hz. Insertion Loss <1 dB Bobbin Material Nylon 6/6 GF-30 Flammability Rating Class HB Coil Finish Wrapping Polyester Film Electrical Insulating Tape Core Size EI125 (1.25 x 1.5) Core Material M-6 29 ga. grain oriented lamination steel Secondary Insulation Clear air dry polyester varnish Termination 15 (38cm) UL1015, 20 ga. lead wire Mounting Steel end bell covers Mounting Orientation Vertical Weight 6 lbs.

Description Design The CXPP series was designed as a high quality output transformers push-pull tube amplifiers. Primary (Input) The input is designed for a 10K Ohms impedance source. Screen/Grid Tap This unit has a 40% screen/grid. Secondary (Output) The output impedance is designed for speakers. Magnet Wire All units are wound with the finest virgin copper magnet wire. All windings use heavy insulated wire to provide excellent manufacturing yield, lower customer cost and superior life. The Core EDCOR uses the finest M6 line grain oriented steel cores. Each unit is hand stacked to assure at least 92% stack. The Bobbin Injection molded Nylon 6/6 with the addition of 30%-35% glass fibers. The addition of glass fibers allows a higher heat deflection temperature and it brings the material to a class HB UL temperature classification. Termination The terminations are UL1015 20 ga. color coded lead wire around 15 inches (38cm) long. Mounting This unit comes with steel end bells for mounting with the use of four screws. See dimensional drawing. Specifications Wattage 30W Primary (input) Impedance 10K ? Screen/Grid Tap 40% Secondary (output) Impedance Depends on model. Winding Configuration Interleave Winding Frequency Response 20~20K Hz., <1dBu THD+Noise <0.1% @ 1K Hz. Insertion Loss <1 dB Bobbin Material Nylon 6/6 GF-30 Flammability Rating Class HB Coil Finish Wrapping Polyester Film Electrical Insulating Tape Core Size EI125 (1.25 x 1.5) Core Material M-6 29 ga. grain oriented lamination steel Secondary Insulation Clear air dry polyester varnish Termination 15 (38cm) UL1015, 20 ga. lead wire Mounting Steel end bell covers Mounting Orientation Vertical Weight 6 lbs.

Description Design The CXPP series was designed as a high quality output transformers push-pull tube amplifiers. Primary (Input) The input is designed for a 10K Ohms impedance source. Screen/Grid Tap This unit has a 40% screen/grid. Secondary (Output) The output impedance is designed for speakers. Magnet Wire All units are wound with the finest virgin copper magnet wire. All windings use heavy insulated wire to provide excellent manufacturing yield, lower customer cost and superior life. The Core EDCOR uses the finest M6 line grain oriented steel cores. Each unit is hand stacked to assure at least 92% stack. The Bobbin Injection molded Nylon 6/6 with the addition of 30%-35% glass fibers. The addition of glass fibers allows a higher heat deflection temperature and it brings the material to a class HB UL temperature classification. Termination The terminations are UL1015 20 ga. color coded lead wire around 15 inches (38cm) long. Mounting This unit comes with steel end bells for mounting with the use of four screws. See dimensional drawing. Specifications Wattage 30W Primary (input) Impedance 10K ? Screen/Grid Tap 40% Secondary (output) Impedance Depends on model. Winding Configuration Interleave Winding Frequency Response 20~20K Hz., <1dBu THD+Noise <0.1% @ 1K Hz. Insertion Loss <1 dB Bobbin Material Nylon 6/6 GF-30 Flammability Rating Class HB Coil Finish Wrapping Polyester Film Electrical Insulating Tape Core Size EI125 (1.25 x 1.5) Core Material M-6 29 ga. grain oriented lamination steel Secondary Insulation Clear air dry polyester varnish Termination 15 (38cm) UL1015, 20 ga. lead wire Mounting Steel end bell covers Mounting Orientation Vertical Weight 6 lbs.

Description Design The CXPP series was designed as a high quality output transformers push-pull tube amplifiers. Primary (Input) The input is designed for a 10K Ohms impedance source. Screen/Grid Tap This unit has a 40% screen/grid. Secondary (Output) The output impedance is designed for speakers. Magnet Wire All units are wound with the finest virgin copper magnet wire. All windings use heavy insulated wire to provide excellent manufacturing yield, lower customer cost and superior life. The Core EDCOR uses the finest M6 line grain oriented steel cores. Each unit is hand stacked to assure at least 92% stack. The Bobbin Injection molded Nylon 6/6 with the addition of 30%-35% glass fibers. The addition of glass fibers allows a higher heat deflection temperature and it brings the material to a class HB UL temperature classification. Termination The terminations are UL1015 20 ga. color coded lead wire around 15 inches (38cm) long. Mounting This unit comes with steel end bells for mounting with the use of four screws. See dimensional drawing. Specifications Wattage 30W Primary (input) Impedance 10K ? Screen/Grid Tap 40% Secondary (output) Impedance Depends on model. Winding Configuration Interleave Winding Frequency Response 20~20K Hz., <1dBu THD+Noise <0.1% @ 1K Hz. Insertion Loss <1 dB Bobbin Material Nylon 6/6 GF-30 Flammability Rating Class HB Coil Finish Wrapping Polyester Film Electrical Insulating Tape Core Size EI125 (1.25 x 1.5) Core Material M-6 29 ga. grain oriented lamination steel Secondary Insulation Clear air dry polyester varnish Termination 15 (38cm) UL1015, 20 ga. lead wire Mounting Steel end bell covers Mounting Orientation Vertical Weight 6 lbs.

Description Design The CXPP series was designed as a high quality output transformers push-pull tube amplifiers. Primary (Input) The input is designed for a 10K Ohms impedance source. Screen/Grid Tap This unit has a 40% screen/grid. Secondary (Output) The output impedance is designed for speakers. Magnet Wire All units are wound with the finest virgin copper magnet wire. All windings use heavy insulated wire to provide excellent manufacturing yield, lower customer cost and superior life. The Core EDCOR uses the finest M6 line grain oriented steel cores. Each unit is hand stacked to assure at least 92% stack. The Bobbin Injection molded Nylon 6/6 with the addition of 30%-35% glass fibers. The addition of glass fibers allows a higher heat deflection temperature and it brings the material to a class HB UL temperature classification. Termination The terminations are UL1015 20 ga. color coded lead wire around 15 inches (38cm) long. Mounting This unit comes with steel end bells for mounting with the use of four screws. See dimensional drawing. Specifications Wattage 30W Primary (input) Impedance 10K ? Screen/Grid Tap 40% Secondary (output) Impedance Depends on model. Winding Configuration Interleave Winding Frequency Response 20~20K Hz., <1dBu THD+Noise <0.1% @ 1K Hz. Insertion Loss <1 dB Bobbin Material Nylon 6/6 GF-30 Flammability Rating Class HB Coil Finish Wrapping Polyester Film Electrical Insulating Tape Core Size EI125 (1.25 x 1.5) Core Material M-6 29 ga. grain oriented lamination steel Secondary Insulation Clear air dry polyester varnish Termination 15 (38cm) UL1015, 20 ga. lead wire Mounting Steel end bell covers Mounting Orientation Vertical Weight 6 lbs.