Rogers LS 4A Hifi Speakers BBC matched Pair in excellent order (tested). Unique opportunity to buy a set of Rogers hand built BBC hifi speakers. They don’t make them to this quality anymore. The modern digitally enhanced speakers do not give the depth and quality of sound that you get out of these. If your an enthusiast and you know your speakers - these are two of the very best vintage ones you can buy. Tiny chip in the casing on one corner ( and I mean tiny, you woul have to search to find it, see image), has been blended back in with a a small amount of enamel paint. Wooded casing is black ash for that retro cool look. Listen to your Vynil how they were meant to be heard through these vintage speakers. Manufacturers Specification below: Rogers LS4a Over the years, our products have earned a worldwide reputation for fine sound quality and high standards of construction. The primary design aims have always been tonal neutrality, low colouration, transparency and wide bandwidth. Another major consideration is consistent and trouble free performance from a system over many years of operation. To ensure this, only high quality components are used in the construction of our loudspeakers. From time to time we introduce a new model, when we do, the new design must possess the strengths of its predecessor, plus other substantial advances, in order to justify the change. Our new designs tend therefore to be few and far between. Constant background research does, however, yeild improvements in our understanding of loudspeaker systems and advances in the performance of drive units. The use of Polypropylene as a cone material, and the recent introduction of high performance metal dome tweeters has meant that advances are possible. The fruits of this research and increased understanding of system behaviour has yielded new systems of advanced design and high quality performance. Specifications Frequency Response: 55 Hz - 20 kHz ±2 dB Impedance: 8 ? Nominal Sensitivity: 88 dB at 1m for 2,83 volts input Power Handling: 150 watts (unclipped programme) Recommended Amplifier Power: 15 - 100 watts per channel Maximum Sound Pressure Level: 105 dBA (pair at 2 m) Drive Units: Tweeter : 19 mm Aluminium dome Bass/Mid-range: Rogers 205 mm Polypropylene coned of advanced acoustic design , with high flux magnet and Kapton voice coil former. Crossover: 8 precision elements crossing over at 3 kHz at 18 dB per octave Bass Loading: Acoustic suspension to form a well damped Butterworth 2nd oreder maximally flat alignment with a -3 dB point at 55 Hz. Distortion: Less than 1% 2nd and 3rd harmonic 50 Hz -20 kHz at 90 dB S.P.L. Connectors: 4 mm binding posts, spaced at 19 mm Recommended Placement: Stands - minimum 500 mm high with loudspeakers angled inwards so that their axes cross just in front of the listener. Cabinet: Critically damped partical board with medite baffle. Finish: High quality synthetic veneer, and black grille cloth Dimensions (H x W x D): 430 x 255 x 245 mm (17 x 10 x 9,7) Weight: 7,8 kg 917 lb) Not going to risk sending these by post, but if a purchaser wishes to organise a courier I am open to that as an option. Thanks for reading.

Roger LS 4A Hifi Speakers BBC matched Pair in excellent order (tested). Unique opportunity to buy a set of Rogers hand built BBC hifi speakers. They don’t make them to this quality anymore. The modern digitally enhanced speakers do not give the depth and quality of sound that you get out of these. If your an enthusiast and you know your speakers - these are two of the very best vintage ones you can buy. Tiny chip in the casing on one corner ( and I mean tiny, you woul have to search to find it, see image), has been blended back in with a a small amount of enamel paint. Wooded casing is black ash for that retro cool look. Listen to your Vynil how they were meant to be heard through these vintage speakers. Manufacturers Specification below: Rogers LS4a Over the years, our products have earned a worldwide reputation for fine sound quality and high standards of construction. The primary design aims have always been tonal neutrality, low colouration, transparency and wide bandwidth. Another major consideration is consistent and trouble free performance from a system over many years of operation. To ensure this, only high quality components are used in the construction of our loudspeakers. From time to time we introduce a new model, when we do, the new design must possess the strengths of its predecessor, plus other substantial advances, in order to justify the change. Our new designs tend therefore to be few and far between. Constant background research does, however, yeild improvements in our understanding of loudspeaker systems and advances in the performance of drive units. The use of Polypropylene as a cone material, and the recent introduction of high performance metal dome tweeters has meant that advances are possible. The fruits of this research and increased understanding of system behaviour has yielded new systems of advanced design and high quality performance. Specifications Frequency Response: 55 Hz - 20 kHz ±2 dB Impedance: 8 ? Nominal Sensitivity: 88 dB at 1m for 2,83 volts input Power Handling: 150 watts (unclipped programme) Recommended Amplifier Power: 15 - 100 watts per channel Maximum Sound Pressure Level: 105 dBA (pair at 2 m) Drive Units: Tweeter : 19 mm Aluminium dome Bass/Mid-range: Rogers 205 mm Polypropylene coned of advanced acoustic design , with high flux magnet and Kapton voice coil former. Crossover: 8 precision elements crossing over at 3 kHz at 18 dB per octave Bass Loading: Acoustic suspension to form a well damped Butterworth 2nd oreder maximally flat alignment with a -3 dB point at 55 Hz. Distortion: Less than 1% 2nd and 3rd harmonic 50 Hz -20 kHz at 90 dB S.P.L. Connectors: 4 mm binding posts, spaced at 19 mm Recommended Placement: Stands - minimum 500 mm high with loudspeakers angled inwards so that their axes cross just in front of the listener. Cabinet: Critically damped partical board with medite baffle. Finish: High quality synthetic veneer, and black grille cloth Dimensions (H x W x D): 430 x 255 x 245 mm (17 x 10 x 9,7) Weight: 7,8 kg 917 lb) Not going to risk sending these by post, but if a purchaser wishes to organise a courier I am open to that as an option. Thanks for reading.

Roger LS 4A Hifi Speakers BBC matched Pair in excellent order (tested). Unique opportunity to buy a set of Rogers hand built BBC hifi speakers. They don’t make them to this quality anymore. The modern digitally enhanced speakers do not give the depth and quality of sound that you get out of these. If your an enthusiast and you know your speakers - these are two of the very best vintage ones you can buy. Tiny chip in the casing on one corner ( and I mean tiny, you woul have to search to find it, see image), has been blended back in with a a small amount of enamel paint. Wooded casing is black ash for that retro cool look. Listen to your Vynil how they were meant to be heard through these vintage speakers. Manufacturers Specification below: Rogers LS4a Over the years, our products have earned a worldwide reputation for fine sound quality and high standards of construction. The primary design aims have always been tonal neutrality, low colouration, transparency and wide bandwidth. Another major consideration is consistent and trouble free performance from a system over many years of operation. To ensure this, only high quality components are used in the construction of our loudspeakers. From time to time we introduce a new model, when we do, the new design must possess the strengths of its predecessor, plus other substantial advances, in order to justify the change. Our new designs tend therefore to be few and far between. Constant background research does, however, yeild improvements in our understanding of loudspeaker systems and advances in the performance of drive units. The use of Polypropylene as a cone material, and the recent introduction of high performance metal dome tweeters has meant that advances are possible. The fruits of this research and increased understanding of system behaviour has yielded new systems of advanced design and high quality performance. Specifications Frequency Response: 55 Hz - 20 kHz ±2 dB Impedance: 8 ? Nominal Sensitivity: 88 dB at 1m for 2,83 volts input Power Handling: 150 watts (unclipped programme) Recommended Amplifier Power: 15 - 100 watts per channel Maximum Sound Pressure Level: 105 dBA (pair at 2 m) Drive Units: Tweeter : 19 mm Aluminium dome Bass/Mid-range: Rogers 205 mm Polypropylene coned of advanced acoustic design , with high flux magnet and Kapton voice coil former. Crossover: 8 precision elements crossing over at 3 kHz at 18 dB per octave Bass Loading: Acoustic suspension to form a well damped Butterworth 2nd oreder maximally flat alignment with a -3 dB point at 55 Hz. Distortion: Less than 1% 2nd and 3rd harmonic 50 Hz -20 kHz at 90 dB S.P.L. Connectors: 4 mm binding posts, spaced at 19 mm Recommended Placement: Stands - minimum 500 mm high with loudspeakers angled inwards so that their axes cross just in front of the listener. Cabinet: Critically damped partical board with medite baffle. Finish: High quality synthetic veneer, and black grille cloth Dimensions (H x W x D): 430 x 255 x 245 mm (17 x 10 x 9,7) Weight: 7,8 kg 917 lb) Not going to risk sending these by post, but if a purchaser wishes to organise a courier I am open to that as an option. Thanks for reading.

Pair of Roger LS 4A Hifi Speakers.Ive owned them for 30 years but not been using them for the past 15 so clearing out.I have just connected them up and they send great still, one has suffered a couple of knocks to the corners and a few paint marks but they have been well treated and are a decent pair of speakers.