Ortofon Concorde Broadcast E Make top sound, not really much used should have 50 till 100 hrs Like ever safe packed in a wooden schedulle Sending in EU cost 15 EuroAsk for other countries Beachten Sie bitte die mich Seite, im Übrigen gelten die gesetzlichen Bestimmungen

Verkaufe 2er Set Ortofon Broadcast E Nadeln Top Zustand, Neuwertig, in Originalverpackung Die Nadeln wurden nur sporadisch genutzt. Ich sammle diese Systeme und habe mehrere. Die Broadcast Nadeln haben einen speziellen elliptischen Schliff und waren die hochwertigsten aus der Pro Serie. ABSOLUT NICHT MEHR ZU BEKOMMEN! Der Preis gilt für das Paar (2 Stück) Verkauf nur als Paar

Verkaufe neuwertige Ortofon Concorde Broadcast E Twin Pack (2 Stück) im Flightcase TOP Zustand Sehr selten Sehr guter Klang Elliptische Nadel Sporadischer Heim Betrieb in Sammlung Wurden durch 40th Anniversary Systeme ersetzt Schon lange nicht mehr zu bekommen Abholung oder Versand mit Zahlung Versandkosten

Ortofon Concorde Broadcast E in OVP Broadcast E Technical data Output voltage at 1000Hz, 5cm/sec. - 6 mV Channel balance at 1kHz - 2 dB Channel separation at 1kHz - 23 dB Channel separation at 15 kHz - 15 dB Frequency response - 20-20.000 Hz +/- 2 dB Tracking ability at 315 Hz at recommended tracking force - 80 ?m Compliance, dynamic lateral - 9 ?m/m N Stylus type - Special Elliptical Stylus tip radius - r/R 13/25 ?m Tracking force range - 2,0-4,0 g (20-40 mN) Tracking force recommended - 3,0 g (30 mN) Tracking angle - 20° Internal impedance, DC resistance - 750 Ohm Internal inductance - 450 mH Recommended load resistance - 47 kOhm Recommended load capacitance - 200-600 pF Cartridge weight - 5 g https://www.hifi-wiki.de/index.php/Ortofon_Concorde_Broadcast_E

Technics SL-1210 MK2 mit Ortofon Concorde Broadcast Tonabnehmer. Selten genutztes Gerät in technisch einwandfreiem Zustand mit sehr wenig Abnutzungsspuren. Die Abdeckung ist leicht verkratzt. Inklusive Ortofon Concorde Broadcast Tonabnehmer. Verkauf erfolgt unter Ausschluss jeglicher Sachmangelhaftung.

2 very rare Ortofon Fonofilm Mono Cartridges Two pin mono for early Ortofon or EMT tonearms May be used on standard arms with an EMT adapter Broadcast quality C-25 requires rebuild, missing bottom cover A-25 with cantilever and stylus intact, missing top logo/ badge This cartridge is a very very early example, with a low serial number of 2823 Postage worldwide with tracking Free postage in Australia

Ortofon 12 banana in vintage Ortofon burnished For the audiophiles all over the world ORTOFON products reach legendary status. And thats rightfully. This is a opportunity to own whats becoming rare and more expensive on the world market. Excellent tonearm for serious music loversBroadcast Tonearm Ortofon AB -309 banana 12 long for Ortofon SPU-G and SME type Headshells ONE OF THE BEST 12 LONG TONEARMSMADE BY ALFRED BOKRANDGERMAN BROADCAST ENGINEER(RADIO+TV) WHY?PHYSICS and GEOMETRY never lies.....THIS ARMWAND IS OPTIMIZED FORLOWEST TRACKING DISTORSION3 THINGS DETERMINE THE QUALITY AND THE PERFORMANCE OF A PERFECT TONEARM:1) EFFEKTIVE LENGHT 2) OVERHANG3) OFFSET ANGLE============================ TONEARM GEOMETRY:EFFEKTIVE LENGTH : 321.459 mm MOUNTING DISTANCE: 309.4mmOVERHANG: 12.66 mmOFFSET ANGLE (DEGREES): 16.9 º _____________________________________________________________========================== ORTOFON 12 AS-309 TONEARM HAVE LESS DISTORSIONS AS THE SME 3012 series I ORTOFON AS-309 12 long compared to SME 3012 series I 309.4 mm mounting distance 294 mm 321.5 mm effektive lenght 305 mm 12.6 mm Over hang 11 mm 16.9 º offset angle(degrees) 16.15 º 1.26 º maximum error º 2.11 º 0.3 % average distorsion 0.36 % 0.46 % maximum distorsion 0.72 % all results taken fromAlignment Calculator Provinylengine page Tonearm geometry with the lowest distortion worldwide, you will hear it immediately the geometry had to be calculated by hand in the 60s, because you did not have any computer calculation programs yet, this could never be the optimum, because the 3 parameters for the geometry are interdependent. When you change only one parameter to 0.5mm the distortions are great. Therefore, tonearms from the 60s can NEVER reach the perfection that is possible with the computer programs today___________________________________This tonearm combines the simple aesthetics of Ortofon Tonearms with the current best armtube geometry currently available only a perfect geometry of the armtube guarantees a low distortion.this is the first and most important thing with a tonearm.not the material, not exotic armtube materials or mimics can eliminate a fundamental distortion that exist due to a wrong and bad geometry.material of the armtube and Vaccination only has an impact on resonance and vibration coming from the plinth (engine vibration and music waves) tonal arms are offered on the market, which cost well over $ 15,000 and are advertised that give the materials the highest in technology (space travel, NASA ect) the geometry of a perfect tonearm with the lowest distorsions consists of: 1) effective length2) overhang3) offset angle nothing more and nothing less these 3 parameters are dependent on each other. This is mathematics and is based on formulas that have absolutely nothing to do with materials. With existing PC calculation programs, anyone can see if their tonearm has the least distortion due to the armtube geometry. This is the only objective method and not the subjective belief in exotic materials or great promises..**************************************************************** positive feedbacks Aligned. It is in an aftermarket VTA tower made for the Groovmaster IIti that was on the table before your arm. I will not going back to the GM!!! Only my $11,000 Glanz MH124 is superior and not by $10,000! I am thrilled at this arms performance richness of tone is its major strong point. Bass is tight super extended and the too end extended and sweet. No ringing or tonal artifacts with this arm. Vocals are on par with the best of the best. Rich defined and harmonical. Thank you sir. Well done! Robin WyattMiyajima Labs USA importer. _______________________________ My Ortofon tonearms go over the SME 3012 and SME 3012R, which costs about 5000 euros. It is only surpassed by a GLANZ for $11,000. Thats not what Im saying, but my customers.see here original mailsDear mr. BokrandI gave myself some time to make sure I wasn’t too hasty in judging. After many hours of listening to my favorite records, which I know very well, I can say that your arm holds up very well the comparison with my beloved SME 3012R, indeed, with the Ortofon SPU is superior in clarity, dynamics (!!!), soundness of bass...Thanks for everythingMassimo Longoni________________________________________________________________________ screw for setting Azimuth 2 DIFFERENT COUNTER WEIGHTS 2 WEIGHTS TOGETHER FOR ORTOFON SPU-G CARTRIDGS UP TO 35 GRAMS or BIG COUNTER WEIGHT SINGLY FOR CARTRIDGES UP TO 20 GRAMS With this construction you have an enormous range of applications for all Cartridges _________________________________________________ ******************************** TONEARM COMES WITH :MOUNTING TEMPLATEMANUALSCREWS AND WASHERS FOR MOUNTING COLLARALLEN KEY FOR ADJUST LIFT DEVICESCREW DRIVER FOR WEIGHTSSCREW DRIVER FOR AZIMUTH ADJUST in the manual you will always find an original sample of the internal wiring WORLDWIDE FREE SHIPPINGTRACKING AND REGISTERED POST-------------------------------------------

Ortofon Broadcast Nadel Hifi Elliptischer Schliff. Fr Hiififans, die dieses Urgestein der Hifi Tonabnehmer zu schtzen wissen. Wie der Name schon sagt, wurde dieser Tonabnehmer im Rundfunk gerne genutzt. Es handelt sich aufgrund der eingestellten Produktion um eine Raritt. Der elliptisch geschliffene Diamant zeichnet sich durch seine Przision in der Abtastung und eine minimale Abnutzung der Rillen aus. Laufzeit der Nadel betrgt geschtzt ca. 6 Stunden, quasi gerade erst eingespielt Fr Ortofon Modelle Concorde und OM nicht passend fr Concorde MK2

Gutes MM-System Made in Denmark! Kaum bespielt, wurde nur testweise ausprobiert - das System ist neuwertig, komplett mit Nadelschutzkappe!Output voltage at 1000Hz, 5cm/sec. - 6 mV Channel balance at 1kHz - 2 dB Channel separation at 1kHz - 23 dB Channel separation at 15 kHz - 15 dB Frequency response - 20-20.000 Hz +/- 2 dB Tracking ability at 315 Hz at recommended tracking force - 80 ?m Compliance, dynamic lateral - 9 ?m/m N Stylus type - Special Elliptical Stylus tip radius - r/R 13/25 ?m Tracking force range - 2,0-4,0 g (20-40 mN) Tracking force recommended - 3,0 g (30 mN) Tracking angle - 20° Internal impedance, DC resistance - 750 Ohm Internal inductance - 450 mH Recommended load resistance - 47 kOhm Recommended load capacitance - 200-600 pF Cartridge weight - 5 g Die auf einigen Fotos zu sehende Technics Einstelllehre ist nicht Teil des Angebots! Lieferung nur Ortofon Concorde mit Nadel Broadcast und Nadelschutzkappe! Privatverkauf: keine Garantie, keine Rücknahme, kein Versand an Packstationen Versicherter Versand mit Sendungsverfolgung