B&O MMC 20E Moving Magnet Stereo Phono Cartridge complete Stylus Guard, B&O Stylus Brush and B&O Tracking Force Gauge. Please review photos; cantilever straight, clean and properly suspended. Stylus tip sharp and uniform. (See photos). This cartridge is suitable for a number of B&O turntables including: Beogram 1102, 1600, 1602, 2200, 2400, 3400.Please confirm this is the correct cartridge for your application before ordering. Packed to arrive safely and shipped quickly. 100% positive feedback seller! No returns on vintage audio and accessories!!

Bang & Olufsen Beogram 1600 Turntable with MMC 20EN Cartridge, Very Nice B&O This Bang & Olufsen Beogram 1600 turntable is in terrific condition, functionally and visually. It is fitted with an MMC 20EN moving coil cartridge, which is in fine shape. For information on B&Os use of the superior moving coil MC cartridge design, see this online article: www.ecoustics.com/ask-an-expert/wtf-moving-magnet-coil-phono-cartridgesThe MMC 20EN was furnished on B&O’s top of the line decks. From Beoworld.com, The extreme lightness of the arm, together with the highly polished nude elliptical diamond carried by the MMC 20EN pickup, resulted in an unusually low Effective Tip Mass (ETM). This means that your records would suffer very little wear, even after continual playing. Neither would they be damaged if the stylus was accidentally skidded across the surface. Thats right. This deck will not scratch your precious vinyl The fully automatic deck and cartridge perform superbly on my Klipsch Cornwall speakers. I have been through the mechanicals, electronics, and cosmetics. The deck top, rosewood trim, dust cover, and cover hinges are all excellent. This turntable is in as nice a condition as you can hope to find. I have done my best to provide good photos. Beogram 1600 Record Deck Product Specifications Speeds 33 - 45 rpm Wow and flutter < 0.09 % Rumble weighted > 62 dB Rumble, unweighted > 42 dB Drive system: Flat Belt Motor Servo controlled DC Power supply 120 V Power consumption 8 W Dimensions W x H x D 44.5 x 8.9 x 33cm Weight 6 kg MMC 20EN Cartridge Produced from: 1979 - 1985 Designed by: Jacob Jensen Finish: Silver metal Recommended tracking force 12 mN / 1.2 g Frequency range: 20 - 20,000 Hz +/- 2 dB Stylus: Elliptical Naked diamond RIAA amplifier: built-in Desirability: 5 (of 5)IMO, the 20EN cartridge sound is superior to the vaunted 20CL – more full bodied, without sacrificing delicate highs. Per Beocentral.com it was well respected for its sound quality and less sensitive to environmental changes than the MMC 20CL. This turntable has twin RCA plugs (not DIN) and a ground for connection to your receiver’s phono inputs. If youd prefer the grey trim around the base, rather than the wood trim, I can make that change for you. Unit will be well packaged, with suspension locked down, for shipment. Guaranteed not DOA. Check our feedback and bid with confidence. Thanks!

Bang & Olufsen B&O BEOGRAM 1600 TURNTABLE Condition is used Shipped with FedEx and packed carefully Overall, in good condition cosmetically tested and working unit has been serviced, making sure the unit is working properly Please see pictures for better description If you have any questions, please let me know If anything wrong with the item, please don’t open a return request. Message me first. Support my small business by following my store on instagram in the link below: instagram.com/joshuasvintagehifi/ Thanks for looking.

B&O BANG AND OLUFSEN BEOGRAM 1600 TURNTABLE WITH MMC 20S STYLUS - GOOD CONDITION Full working Good condition Free Uk Delivery

Original Bang & Olufsen MMC4000 Cartridge/StylusUk stock ready for dispatch Checked on a spectrum analyser, delicate, accurate and precise matching perfectly to its published specificationTracking perfectly with 1gram vertical tracking forceNo stock images what you see is what you getMMC4000 Product SpecificationsElliptical naked diamond Radius of curvature 5 x 1,7 mm Frequency range 20 - 25000 Hz+/- 1,5dB Channel separation 1000Hz > 20dB 40 - 10000Hz > 20dB Channel difference <1,5dB Intermodulation <1% Recommended stylus pressure 1g Compliance 30 x 10(-6)cm/dyne Effective tip mass 0,4mg Output mV/cm/sec. 0,6mV/47kOhmsMMC4000Large photoManufactured: 1974 - 1980Designer: Subir PramanikColours: Silver MMC 4000This pick-up cartridge was specially designed for use in Bang & Olufsen record-players with tangential arms.It was designed to track SQ 4 channel matrix records and tracked both mono and stereo records extremely well. It was fitted to Beogram 4002. The stylus was an elliptical naked diamond, radii 5x17u. Recommended tracking force was 1g. Each MMC 4000 was designed as an integrated unit. This meant that all critical components were designed and constructed as an entity in order to give optimum performance. The stylus unit was not separately replaceable as it was part of the integrated unit. Frequency range was 20-30,000 Hz ± 3 dB. Effective tip mass was a mere 0.5 mg and compliance was higher than 30x10-6 cm/dyne.

Original Bang & Olufsen MMC20E Cartridge/StylusUk stock ready for dispatch Checked on a spectrum analyser, delicate, accurate and precise.Tracking perfectly.Sounds great.Stock images appearance will vary slightly.BANG & OLUFSEN MMC20E CART & STYLUS BEOGRAM 6000 4000 8000 BEOCENTER 7000 7002 3600 4600Inspected, tested - see images MMC means Moving Micro-Cross Titanium-bonded naked elliptical diamond, to reduce record wear and maintain optimum surface contact Effective Tip Mass of mg 0,4 this is what preserves your vinyl! MMC20EManufactured: 1979 - 1985 Designer: Jacob Jensen Colours: BlackPrior to the release of MMC1 - 5 cartridges, Bang & Olufsen had the following MMC range of combined styli and cartridges:MMC cartridges were available with standard ½ mounting brackets, or with easy plug-in, lightweight connectors. These enabled you to mount MMC cartridges onto non-Bang & Olufsen arms. The cartridges plugged directly into Beogram pickup arms without additional mounting gearMMC 20 S was a stereo cartridge with a spherical framed diamondMMC 20 E was fitted with a framed elliptical diamond which has a high polishMMC 20EN had a naked elliptical diamond, mounted on a tiny tapered cantileverMMC 20 CL utilised a Contact Line naked diamond mounted on a single crystal sapphire cantilever. This shape ensures maximum groove contact. This was the most highly-specified cartridge in the MMC 20 rangeIn 1958, Bang & Olufsen introduced the first stereo pickup cartridge ever made in Europe. This was called the SP1. Since then, many design innovations and the creative use of new materials have kept B&Os cartridges at the forefront of audio technology. By 1979 - 80, Bang & Olufsens cartridges were represented by the MMC 20 series. MMC stands for Moving Micro-Cross; the patented moving-iron principle upon which all B&O cartridges were based. This unique system employed a cross-shaped armature which, among other advantages, guaranteed exceptional stereo separation since each channel moves on a separate axis.The job of any pickup cartridge is to transform the records physical profile (groove modulation) into corresponding electrical signals (which are then amplified or enlarged by the amplifier and turned into audible sound waves by the loudspeaker.A cartridge must perform three separate and exacting tasks if it is to do this job successfully. It must function mechanically (the movements of the stylus in the groove); it must function magnetically (using the physical movements to create changes in a magnetic field); and it must function electrically (using the changes in magnetic flux to generate an electrical current). At each stage, one type of energy is transferred into another, quite different, type. And the transfer must be perfect, with no energy lost and none added from extraneous sources.No cartridge will ever reach this ideal unless the Laws of Physics can be repealed. However, by understanding the relationships between the three transfer stages and continually applying refined engineering techniques, B&Os belief was that each stage of cartridge improvement would bring each successive cartridge closer to the ideal. The MMC20 series therefore represented the closest that modern technology at that time, could possibly afford.Record wear and the cartridgeIf you take music seriously the value of your record collection is likely to be high. Many of your records are likely to be irreplaceable. You will also know that the signals pressed into your vinyl discs are very fragile indeed. The pickup cartridge can be the discs worse enemy since an ill-suited cartridge can mark a record for life in a single play.While B&O is aware that cartridge specifications are inter-related, their research shows consistently that Effective Tip Mass (ETM) is one of the major factors affecting record wear. ETM is the equivalent of the amount of inertia the groove sees in moving or accelerating the stylus tip. Consequently, the higher the ETM value, the higher the force required for a given constant acceleration. Obviously, more force results in more wear.Three elements contribute to ETM. The stylus tip (diamond) contributes with its entire weight and mass. The armature contributes between 5 - 20% of its weight and mass; the cantilever around 30%. B&O has been able to reduce ETM substantially by refining these elements and building them into an integrated unit. The result is a system which not only reduces damage to the groove walls dramatically, but also provides exceptional performance at all frequencies.Bang & Olufsen cartridges have always been highly acclaimed for their low ETM values. The ETM of the MMC 20CL is a mere 0,3mg and in the standard MMC 20 range,, only 0,5mg.MMC cartridges were manufactured by Bang & Olufsen as totally integrated units. This means that the elements were matched, balanced and sealed at the factory. Using a computer-supported testing programme,, each sealed unit was meticulously tested and its performance information automatically registered and packed with each cartridge. The information given included output voltage, relative voltage output (channel balance), channel separation and frequency response. Individually-calibrated frequency response curves were also supplied with the higher-specified MMC 20CL cartridges.

Original Bang & Olufsen MMC20E Cartridge/StylusUk stock ready for dispatch Checked on a spectrum analyser, delicate, accurate and precise.Tracking perfectly.Sounds great.Stock images appearance will vary slightly.BANG & OLUFSEN MMC20E CART & STYLUS BEOGRAM 6000 4000 8000 BEOCENTER 7000 7002 3600 4600Inspected, tested - see images MMC means Moving Micro-Cross Titanium-bonded naked elliptical diamond, to reduce record wear and maintain optimum surface contact Effective Tip Mass of mg 0,4 this is what preserves your vinyl! MMC20EManufactured: 1979 - 1985 Designer: Jacob Jensen Colours: BlackPrior to the release of MMC1 - 5 cartridges, Bang & Olufsen had the following MMC range of combined styli and cartridges:MMC cartridges were available with standard ½ mounting brackets, or with easy plug-in, lightweight connectors. These enabled you to mount MMC cartridges onto non-Bang & Olufsen arms. The cartridges plugged directly into Beogram pickup arms without additional mounting gearMMC 20 S was a stereo cartridge with a spherical framed diamondMMC 20 E was fitted with a framed elliptical diamond which has a high polishMMC 20EN had a naked elliptical diamond, mounted on a tiny tapered cantileverMMC 20 CL utilised a Contact Line naked diamond mounted on a single crystal sapphire cantilever. This shape ensures maximum groove contact. This was the most highly-specified cartridge in the MMC 20 rangeIn 1958, Bang & Olufsen introduced the first stereo pickup cartridge ever made in Europe. This was called the SP1. Since then, many design innovations and the creative use of new materials have kept B&Os cartridges at the forefront of audio technology. By 1979 - 80, Bang & Olufsens cartridges were represented by the MMC 20 series. MMC stands for Moving Micro-Cross; the patented moving-iron principle upon which all B&O cartridges were based. This unique system employed a cross-shaped armature which, among other advantages, guaranteed exceptional stereo separation since each channel moves on a separate axis.The job of any pickup cartridge is to transform the records physical profile (groove modulation) into corresponding electrical signals (which are then amplified or enlarged by the amplifier and turned into audible sound waves by the loudspeaker.A cartridge must perform three separate and exacting tasks if it is to do this job successfully. It must function mechanically (the movements of the stylus in the groove); it must function magnetically (using the physical movements to create changes in a magnetic field); and it must function electrically (using the changes in magnetic flux to generate an electrical current). At each stage, one type of energy is transferred into another, quite different, type. And the transfer must be perfect, with no energy lost and none added from extraneous sources.No cartridge will ever reach this ideal unless the Laws of Physics can be repealed. However, by understanding the relationships between the three transfer stages and continually applying refined engineering techniques, B&Os belief was that each stage of cartridge improvement would bring each successive cartridge closer to the ideal. The MMC20 series therefore represented the closest that modern technology at that time, could possibly afford.Record wear and the cartridgeIf you take music seriously the value of your record collection is likely to be high. Many of your records are likely to be irreplaceable. You will also know that the signals pressed into your vinyl discs are very fragile indeed. The pickup cartridge can be the discs worse enemy since an ill-suited cartridge can mark a record for life in a single play.While B&O is aware that cartridge specifications are inter-related, their research shows consistently that Effective Tip Mass (ETM) is one of the major factors affecting record wear. ETM is the equivalent of the amount of inertia the groove sees in moving or accelerating the stylus tip. Consequently, the higher the ETM value, the higher the force required for a given constant acceleration. Obviously, more force results in more wear.Three elements contribute to ETM. The stylus tip (diamond) contributes with its entire weight and mass. The armature contributes between 5 - 20% of its weight and mass; the cantilever around 30%. B&O has been able to reduce ETM substantially by refining these elements and building them into an integrated unit. The result is a system which not only reduces damage to the groove walls dramatically, but also provides exceptional performance at all frequencies.Bang & Olufsen cartridges have always been highly acclaimed for their low ETM values. The ETM of the MMC 20CL is a mere 0,3mg and in the standard MMC 20 range,, only 0,5mg.MMC cartridges were manufactured by Bang & Olufsen as totally integrated units. This means that the elements were matched, balanced and sealed at the factory. Using a computer-supported testing programme,, each sealed unit was meticulously tested and its performance information automatically registered and packed with each cartridge. The information given included output voltage, relative voltage output (channel balance), channel separation and frequency response. Individually-calibrated frequency response curves were also supplied with the higher-specified MMC 20CL cartridges.

Original Bang & Olufsen MMC4000 Cartridge/StylusUk stock ready for dispatch Checked on a spectrum analyser, delicate, accurate and precise matching perfectly to its published specificationTracking perfectly with 1gram vertical tracking forceNo stock images what you see is what you getMMC4000 Product SpecificationsElliptical naked diamond Radius of curvature 5 x 1,7 mm Frequency range 20 - 25000 Hz+/- 1,5dB Channel separation 1000Hz > 20dB 40 - 10000Hz > 20dB Channel difference <1,5dB Intermodulation <1% Recommended stylus pressure 1g Compliance 30 x 10(-6)cm/dyne Effective tip mass 0,4mg Output mV/cm/sec. 0,6mV/47kOhmsMMC4000Large photoManufactured: 1974 - 1980Designer: Subir PramanikColours: Silver MMC 4000This pick-up cartridge was specially designed for use in Bang & Olufsen record-players with tangential arms.It was designed to track SQ 4 channel matrix records and tracked both mono and stereo records extremely well. It was fitted to Beogram 4002. The stylus was an elliptical naked diamond, radii 5x17u. Recommended tracking force was 1g. Each MMC 4000 was designed as an integrated unit. This meant that all critical components were designed and constructed as an entity in order to give optimum performance. The stylus unit was not separately replaceable as it was part of the integrated unit. Frequency range was 20-30,000 Hz ± 3 dB. Effective tip mass was a mere 0.5 mg and compliance was higher than 30x10-6 cm/dyne.

Bang & Olufsen B&O Beogram 1600 Type T5712 Turntable With Stylus - for Parts See More in My Store, Thanks! https://www.ebay.com/str/califorstyle Returns: We want you to be completely happy with your purchase so we have adopted a generous 30 day return policy. Buyer must return item within 30 days. A refund will be given if the item is returned in original shipping condition and received by the Seller.

Bang & Olufsen - B&O - Complete system from the late 1970s. Including tape, tuner, record player and 4 speakers. Not tested to see if working. One of the hinges on the control lid needs adjusting as wont shut fully. Really nice retro system and was top of the range in its day. Selling as spares or repairs as untested. Collection only from Okehampton in Devon

Beogram 1600 B&O turntable. This unit is working and in very nice cosmetic condition, some light marks to a very well presented perspex cover. All working, but needs setting up and adjustment of arm lift height etc to get perfectly set - currently it does not lift high enough when returning across the record, but Auto return all works once this is adjusted. Beogram 1600 was manufactured primarily for the US markets; therefore in the overall scheme of things, there weren’t many of these around. It will need a combined cartridge/stylus. BeoGram 1600 technical specificationsTypes: US 5712 (1978 - Jan 1986) F 5713 (1980 - Jan 1983) Speeds / control range 33 - 45 rpm. / > +/- 3 % Wow and flutter, DIN < +/- 0.09 % Rumble weighted > 62 dB Rumble unweighted > 42 dB Motor / drive system: Servo-controlled DC / Belt Pickup: MMC 20 E Recommended tracking force 15 mN / 1.5 g Power supply: 5712: 120V 5713: 220V Power consumption 8 W Dimensions W x H x D / Weight 44.5 x 8.9 x 33 cm / 6 kg Type: US 5712 (1977 - Dec 1978) Speeds / control range 33 - 45 rpm. / > +/- 3 % Wow and flutter, DIN < +/- 0.09 % Rumble weighted > 62 dB Rumble unweighted > 42 dB Motor / drive system: Servo-controlled DC / Belt Recommended tracking force 15 mN / 1.5 g Power supply: 120 V Power consumption 8 W Dimensions: W x H x D / Weight 44.5 x 8.9 x 33 cm / 6 kg