TESTED AND IN GOOD WORKING AND SOUNDING CONDITION. SHOWING MINIMAL WEAR FROM NORMAL USE. NICE SUB SOUND. SORRY NO RETURNS ACCEPTED AS OF SIZE AND WEIGHT SHIPS TO THE LOWER 48 UNITED STATES ONLY ANY QUESTIONS PLEASE ASK.

Pair Polk Audio (MC80) High Performance In-ceiling Speaker - White. Perfect condition although missing one (1 of 4) of the ceiling clamps as you can see in the bottom right hand corner of the forth picture. This is not needed though. Three existing clamps tighten it to the ceiling more than adequately. Speaker was only used a few times before a renovation had it removed. **NO BOX**

This is for two (2) Polk Audio (MC80) High Performance In-ceiling Speakers - White. Brand new in box. SpecsTweeter Size0.75Midrange SizeN/ASpeaker ShapeRoundWoofer Size8Cutout Width9.375Cutout Height9.375Mounting Depth4.0625Power Range (Watts)20-100Sensitivity92 dBImpedance (Ohms)8Frequency Response50-20kHz

Car Audio & VideoPro AudioMarine AudioLighting Karaoke Home/Portable Audio Polk Audio PAD4000.4 4-Channel 800 Watt RMS Car Amplifier --> Click Thumbnails to Enlarge Condition and Warranty Condition: USED Warranty: 1 YEAR AUDIOSAVINGS Product Description Authorized Polk Dealer! Features: Polk Audio PAD4000.4 4-Channel 800 Watt RMS Car Audio Amplifier Amp PA D4000.4 Super-Eefficient Class D Design—Runs much cooler than conventional amps. High-Speed MOSFET—Switching power supply. Toroidal Transformers—Help keep the amplifier’s sleek design under 2 tall while ensuring plenty of clean, efficient power. Protection—Thermal, DC offset, reverse DC voltage and short circuit protection. Nickel-Plated Wire Terminals & RCA Connectors— Ensure maximum signal transfer. Front & Rear Level Controls—Adjust the gain of the front and rear channels to match the output voltage from your head unit. Low-Pass & High-Pass Frequency Controls— Enables you to adjust crossover overlap for better blending of speakers. Front & Rear BPF, FULL, HPF Switches— Selects full range, high pass filter, or bandpass filter to dial in your speaker blending. Channel Mode Switch (ST/4Ch)—In the Stereo position, the amplifier will send the same signal to front and rear channels. Stainless Steel Hardware—Used throughout won’t corrode in humid environments. Specifications: Type: Bridgeable Class D MOSFET Channels: 4 channel RMS Continuous Power @ 4 Ohms: 125 W x 4 RMS Continuous Power @ 2 Ohms: 200 W x 4 Power Bridged @ 4 Ohms: 400 W x 2 Distortion at Rated Power: <0.1% Minimum Impedance Bridged: 4 Ohms Minimum Impedance Not Bridged: 2 Ohms Signal-to-noise Ratio: 105 dB Frequency Response: 20 Hz-20 kHz Damping Factor: >100 Crossover Filter Slope: 12 dB/octave Filter Switch (Front): 3-position (HPF, Full, BPF) High Pass Filter Frequency Range (Front): 20 Hz - 4 kHz Low Pass Filter Frequency Range (Front): 50 Hz - 5 kHz Front Gain Control: 200 mV - 6 V Filter Switch (Rear): 3-position (HPF, Full, BPF) High Pass Filter Frequency Range (Rear): 20 Hz - 4 kHz Low Pass Filter Frequency Range (Rear): 50 Hz - 5 kHz Rear Gain Control: 200 mV - 6 V Line Level Inputs LED Power Indicator LED Protection Indicator Supply Voltage: 10 V - 16 V Fusing & Power/Type: (1) 40A (1) 35A ATC Power Connections: 4 AWG Ground Connections: 4 AWG Speaker Connections: 12 AWG Height: 1 13/16 (46 mm) Depth: 6 3/4 (171.5 mm) Width: 10 15/16 (277.8 mm) Width w/ Terminal Adaptor: 11 11/16 (296.9 mm) Weight: 5 lbs (2.7 kg) Advantages of buying from an authorized seller: Best prices - We sell all Polk Audio Products at great prices Full Factory Warranty Lifetime Customer Service by Polk Audio product experts Guaranteed legitimate and authentic merchandise Please note: If you purchase Polk Audio from an unauthorized seller then you are taking a big risk. You will not have any manufacturers warranty, and there is no guarantee that the item is authentic, brand new, or even working. Return Policy AudioSavings Return Policy: At Audiosavings, we strongly believe in customer satisfaction and therefore offer free return shipping within 30 days of purchase on all items returned to us within the continental USA. Prior to returning merchandise, contact us and we will give you a return authorization # and a return label. You may return this item for a refund within 30 DAYS of purchase. Warranty Repair/Exchange Period: 1 YEAR If your item is defective or you want to return it for any reason within the first 30 days of when it was delivered to you; you have the following options: We will send you a pre-paid shipping label to replace the item for a brand new one. We will send you a pre-paid shipping label to exchange the item for another item of your choice. If the item you chose is more or less money we will work out the price difference with you. If you are returning a working item in used condition for a refund there will be a 20% used item fee deducted from your refund. All replacements and exchanges are free. Replacement/Processing Time: Your replacement or refund will process within 3-5 business days of when we receive the item. Please note items with physical damage un-related to shipping are not covered under warranty. Registered software cannot be returned. You MUST notify us within 48 hours if you receive an item that was damaged during shipping. Process for returning items Please email us with your eBay user ID, Item code / model #, Condition of the item, and the reason for your return. Please also indicate whether you would like a replacement, an exchange, or a refund. We will supply you with a reference number (RMA #) to put on the package which will ensure quick processing of your return. All returns require a RMA# to be returned back to our facility. Item Code: PAD4000.4* Home / About Us / Contact Us / Returns / FAQs Copyright © 2016 Audio Savings, All rights reserved. | eBay Template Design

The Subwoofer is in great shape and would be good for any 5.1, 6.1 7.1 audio system. But there are a Two cosmetic thing with the subwoofer. The front speaker screen has some small imperfection and there is a scuff running down the lower left side of the subwoofer. Other than those two things the Subwoofer is in working order. All the info on the Subwoofer is below, Thanks for reading Powered subwoofer: RM6750 bass-reflex50-watt RMS amp8 front-firing Dynamic Balance woofer11W x 15-7/8H x 13-3/8DMaterials: The RM6750 subwoofer is made of durable MDF with a black vinyl finish.Recommended Hookup: The subwoofer can be connected several different ways, utilizing the speaker level inputs and outputs, or the Line input. The subwoofer features spring clip terminals for the speaker level inputs and outputs, plus a stereo RCA line input. The recommended hookup methods are as follows:Recommended Hookup A: Polk Audio recommends connecting the amplifiers left and right front channels to the speaker level inputs of the subwoofer and the front left and right satellite speakers to the subwoofers speaker level output. The center and surround speakers are directly connected to the amplifier. The amplifiers bass management/speaker setup should be configured with the front left and right speakers set to Large and the Subwoofer set to Off or None.Recommended Hookup B: An alternate hookup method is for the subwoofer and front speakers to be connected in parallel directly to the amplifiers front outputs. The center and surround speakers are directly connected to the amplifier. The bass management setup is the same as Recommended Hookup A.Line Input: This stereo RCA input allows you to connect to an unfiltered subwoofer output on a receiver. You will need a Y adapter to connect a mono subwoofer cable to the stereo line input.Phase Switch: Speaker positioning can sometimes cause subwoofers to work against satellite speakers instead of with them, creating frequency canceling and a dramatic loss of bass. When this occurs, you can switch the phase of the subwoofer driver from Normal (0°) to Reverse (180°), to enhance the bass attack.Volume: The subwoofer has a separate volume level, allowing you to adjust the subwoofer relative to the remainder of the sound system.Slot-loaded Bass Vent: The powered subwoofer features a slot-loaded bass vent on the front panel just beneath the woofer. The slot, 9 x 1, dramatically lessens turbulence, noise and distortion, enabling the subwoofer to play precise, thunderous bass.Subwoofer Positioning: The RM6750 subwoofer is not magnetically shielded and may cause picture interference if it is placed in close proximity to a TV or computer monitor. For best performance, the subwoofer should be placed at least six inches away from a wall.

POLK AUDIO BLACKSTONE RM6880 Suround Sound Set of 6 Home Theater Speaker System EXCELLENT CONDITION. PLEASE LOOK UP THE ABOVE PICTURES FOR MORE DETAILS. EXPECT THE BEST QUALITY. ALWAYS AUTHENTICITY GUARANTEEDReturn: return are accepted within 30 days from receipt of merchandise.Shipping: we ship the same day. free priority mail shipping within the US. Payment: Please pay as soon as possible after winning an auction, as that will allow us to ship your item to you next day. Feel free to ask for more. Notes:All clothes come from a Smoke Free Home.

The Subwoofer is in great shape and would be good for any 5.1, 6.1 7.1 audio system. But there are a Two cosmetic thing with the subwoofer. The front speaker screen has some small imperfection and there is a scuff running down the lower left side of the subwoofer. Other than those two things the Subwoofer is in working order. All the info on the Subwoofer is below, Thanks for reading Powered subwoofer: RM6750 bass-reflex50-watt RMS amp8 front-firing Dynamic Balance woofer11W x 15-7/8H x 13-3/8DMaterials: The RM6750 subwoofer is made of durable MDF with a black vinyl finish.Recommended Hookup: The subwoofer can be connected several different ways, utilizing the speaker level inputs and outputs, or the Line input. The subwoofer features spring clip terminals for the speaker level inputs and outputs, plus a stereo RCA line input. The recommended hookup methods are as follows:Recommended Hookup A: Polk Audio recommends connecting the amplifiers left and right front channels to the speaker level inputs of the subwoofer and the front left and right satellite speakers to the subwoofers speaker level output. The center and surround speakers are directly connected to the amplifier. The amplifiers bass management/speaker setup should be configured with the front left and right speakers set to Large and the Subwoofer set to Off or None.Recommended Hookup B: An alternate hookup method is for the subwoofer and front speakers to be connected in parallel directly to the amplifiers front outputs. The center and surround speakers are directly connected to the amplifier. The bass management setup is the same as Recommended Hookup A.Line Input: This stereo RCA input allows you to connect to an unfiltered subwoofer output on a receiver. You will need a Y adapter to connect a mono subwoofer cable to the stereo line input.Phase Switch: Speaker positioning can sometimes cause subwoofers to work against satellite speakers instead of with them, creating frequency canceling and a dramatic loss of bass. When this occurs, you can switch the phase of the subwoofer driver from Normal (0°) to Reverse (180°), to enhance the bass attack.Volume: The subwoofer has a separate volume level, allowing you to adjust the subwoofer relative to the remainder of the sound system.Slot-loaded Bass Vent: The powered subwoofer features a slot-loaded bass vent on the front panel just beneath the woofer. The slot, 9 x 1, dramatically lessens turbulence, noise and distortion, enabling the subwoofer to play precise, thunderous bass.Subwoofer Positioning: The RM6750 subwoofer is not magnetically shielded and may cause picture interference if it is placed in close proximity to a TV or computer monitor. For best performance, the subwoofer should be placed at least six inches away from a wall.

The Subwoofer is in great shape and would be good for any 5.1, 6.1 7.1 audio system. But there are a Two cosmetic thing with the subwoofer. The front speaker screen has some small imperfection and there is a scuff running down the lower left side of the subwoofer. Other than those two things the Subwoofer is in working order. All the info on the Subwoofer is below, Thanks for reading Powered subwoofer: RM6750 bass-reflex50-watt RMS amp8 front-firing Dynamic Balance woofer11W x 15-7/8H x 13-3/8DMaterials: The RM6750 subwoofer is made of durable MDF with a black vinyl finish.Recommended Hookup: The subwoofer can be connected several different ways, utilizing the speaker level inputs and outputs, or the Line input. The subwoofer features spring clip terminals for the speaker level inputs and outputs, plus a stereo RCA line input. The recommended hookup methods are as follows:Recommended Hookup A: Polk Audio recommends connecting the amplifiers left and right front channels to the speaker level inputs of the subwoofer and the front left and right satellite speakers to the subwoofers speaker level output. The center and surround speakers are directly connected to the amplifier. The amplifiers bass management/speaker setup should be configured with the front left and right speakers set to Large and the Subwoofer set to Off or None.Recommended Hookup B: An alternate hookup method is for the subwoofer and front speakers to be connected in parallel directly to the amplifiers front outputs. The center and surround speakers are directly connected to the amplifier. The bass management setup is the same as Recommended Hookup A.Line Input: This stereo RCA input allows you to connect to an unfiltered subwoofer output on a receiver. You will need a Y adapter to connect a mono subwoofer cable to the stereo line input.Phase Switch: Speaker positioning can sometimes cause subwoofers to work against satellite speakers instead of with them, creating frequency canceling and a dramatic loss of bass. When this occurs, you can switch the phase of the subwoofer driver from Normal (0°) to Reverse (180°), to enhance the bass attack.Volume: The subwoofer has a separate volume level, allowing you to adjust the subwoofer relative to the remainder of the sound system.Slot-loaded Bass Vent: The powered subwoofer features a slot-loaded bass vent on the front panel just beneath the woofer. The slot, 9 x 1, dramatically lessens turbulence, noise and distortion, enabling the subwoofer to play precise, thunderous bass.Subwoofer Positioning: The RM6750 subwoofer is not magnetically shielded and may cause picture interference if it is placed in close proximity to a TV or computer monitor. For best performance, the subwoofer should be placed at least six inches away from a wall.

This is for two (2) Polk Audio (MC80) High Performance In-ceiling Speakers - White. Brand new in box. SpecsTweeter Size0.75Midrange SizeN/ASpeaker ShapeRoundWoofer Size8Cutout Width9.375Cutout Height9.375Mounting Depth4.0625Power Range (Watts)20-100Sensitivity92 dBImpedance (Ohms)8Frequency Response50-20kHz

Polk Audio (MC80) High Performance In-ceiling Speaker - White.

The Subwoofer is in great shape and would be good for any 5.1, 6.1 7.1 audio system. But there are a Two cosmetic thing with the subwoofer. The front speaker screen has some small imperfection and there is a scuff running down the lower left side of the subwoofer. Other than those two things the Subwoofer is in working order. All the info on the Subwoofer is below, Thanks for reading Powered subwoofer: RM6750 bass-reflex50-watt RMS amp8 front-firing Dynamic Balance woofer11W x 15-7/8H x 13-3/8DMaterials: The RM6750 subwoofer is made of durable MDF with a black vinyl finish.Recommended Hookup: The subwoofer can be connected several different ways, utilizing the speaker level inputs and outputs, or the Line input. The subwoofer features spring clip terminals for the speaker level inputs and outputs, plus a stereo RCA line input. The recommended hookup methods are as follows:Recommended Hookup A: Polk Audio recommends connecting the amplifiers left and right front channels to the speaker level inputs of the subwoofer and the front left and right satellite speakers to the subwoofers speaker level output. The center and surround speakers are directly connected to the amplifier. The amplifiers bass management/speaker setup should be configured with the front left and right speakers set to Large and the Subwoofer set to Off or None.Recommended Hookup B: An alternate hookup method is for the subwoofer and front speakers to be connected in parallel directly to the amplifiers front outputs. The center and surround speakers are directly connected to the amplifier. The bass management setup is the same as Recommended Hookup A.Line Input: This stereo RCA input allows you to connect to an unfiltered subwoofer output on a receiver. You will need a Y adapter to connect a mono subwoofer cable to the stereo line input.Phase Switch: Speaker positioning can sometimes cause subwoofers to work against satellite speakers instead of with them, creating frequency canceling and a dramatic loss of bass. When this occurs, you can switch the phase of the subwoofer driver from Normal (0°) to Reverse (180°), to enhance the bass attack.Volume: The subwoofer has a separate volume level, allowing you to adjust the subwoofer relative to the remainder of the sound system.Slot-loaded Bass Vent: The powered subwoofer features a slot-loaded bass vent on the front panel just beneath the woofer. The slot, 9 x 1, dramatically lessens turbulence, noise and distortion, enabling the subwoofer to play precise, thunderous bass.Subwoofer Positioning: The RM6750 subwoofer is not magnetically shielded and may cause picture interference if it is placed in close proximity to a TV or computer monitor. For best performance, the subwoofer should be placed at least six inches away from a wall.

TESTED AND IN GOOD WORKING AND SOUNDING CONDITION. SHOWING MINIMAL WEAR FROM NORMAL USE. NICE SUB SOUND. SORRY NO RETURNS ACCEPTED AS OF SIZE AND WEIGHT SHIPS TO THE LOWER 48 UNITED STATES ONLY ANY QUESTIONS PLEASE ASK.

Polk Audio Rm50t Rm8000t.

Used Polk Audio RM705 subwoofer.Tested, working perfectly.Some minor cosmetics flaws, scuff, scatch.

Polk Audio (MC80) High Performance In-ceiling Speaker - White.