This turntable is brand new, never used. But it is an open box and the box is pretty rough. See pic. But all the packing materials inside are not damaged. I did plug it in to make sure it turns on. Introducing the Denon DP-400 turntable in white color. This high-quality record player features a dust cover and the ability to play at three different speed settings - 45RPM, 33.3RPM, and 78RPM. The model is Denon DP400, making it a reliable choice for music lovers. The item is brand new and comes in an open box, ready for use. Its sleek design makes it a perfect fit for any home audio setup. Don't miss out on the opportunity to own this top-of-the-line record player.

Denon Poa-4400 Mono-Endstufen 2 Stück!. Ich verkaufe 2 Mono- Endstufen der Marke Denon. Die Mono Endstufen sind die Denon Poa-4400. Ich brauche sie nicht mehr und deshalb möchte ich sie verkaufen. Die Endstufen sind in einen guten Zustand. Daten Allgemein Hersteller: Denon Modell: POA-4400 Baujahre: 1987 - 1988 Hergestellt in: Japan Farbe: Schwarz Fernbedienung: Nein Leistungsaufnahme: 350 Watt (IEC) Abmessungen: 310 x 192 x 420 mm (BxHxT) Gewicht: 10,3 kg Anschlüsse Anzahl der Eingänge: Cinch 1 V /25 KOhm XLR 1 V/10 KOhm Anzahl der Ausgänge: 2x Lautsprecher Technische Daten Dauerleistung (bei Klirrfaktor) 8 Ohm: 150 Watt <0,02% 4 Ohm: 250 Watt DIN Dynamikleistung 8 Ohm: 4 Ohm: 400 Watt 2 Ohm: 500 Watt 1 Ohm: 600 Watt Gesamtklirrfaktor: < 0,002% (-3 dB bei Nennleistung an 8 Ohm) Dämpfungsfaktor: Frequenzgang: 1 Hz - 300 kHz (+0/-3dB, 1 W) Signalrauschabstand: 123 dB (IHF, A-Bewertung, XLR)

Denon DRA 400 Precision Audio Component AM/FM Tuner Stereo AMP Receiver Used, works - Bought at an estate sale, history unknown Tape Deck Not Included Video available of working FM and Cassette under extra kart parts youtube channel - message for link Below description found online and buyer must confirm accuracy- reference only - Info from gamma electronics - XYZ Manufacturers Specifications FM Tuner Section: Usable Mono Sensitivity: 10.3 dBf. S/N Ratio: Mono, 75 dB; stereo, 72 dB. THD at 1 kHz: Mono, 0.1%; stereo, 0.2%. Capture Ratio: 1.2 dB. Image Rejection: 45 dB. AM Suppression: 60 dB. Stereo Separation, 1 kHz: 50 dB. Frequency Response: 10 Hz to 15 kHz, +0.2,-1.5 dB. AM Tuner Section: Usable Sensitivity: 15 dB. S/N Ratio: 55 dB. Amplifier Section: Power Output: 40 watts per channel, 8 ohms, 20 Hz to 20 kHz (50 watts, 1 kHz, 4 ohms). THD: 0.02%, 8 ohms. Damping Factor: 80, 1 kHz, 8 ohms. Input Sensitivity: MM phono, 2.5 mV; MC phono, 0.25 mV; high level, 150 mV. Maximum Phono Input Level: MM phono, 200 mV; MC phono, 20 mV. Frequency Response: Phono, RIAA 0.5 dB; high level, 20 Hz to 20 kHz, 0.5 dB. S/N Ratio: MM phono, 80 dB; MC phono, 62 dB; high level, 96 dB. Tone Control Range: 10 dB at 50 Hz and 10 kHz. Subsonic Filter Cutoff: 18 Hz, 6 dB per octave. General Specifications: Power Consumption: 130 watts. Dimensions: 17.1 in. (43.4 cm) W x 4.4 in. (11.2 cm) H x 16.1 in. (40.8 cm) D. Weight: 19.8 lbs. (9.0 kg). Price: $399.95. Company Address: 61 Law Dr., Fairfield, N.J. 07006. As so often happens with advances in audio technology, new features are first incorporated in top-of-the-line separate components which are beyond the reach of all but the most affluent of audio enthusiasts. Later on, these features filter down to high-powered, high-priced all-in-one receiv ers, where a larger audience is potentially available. Finally, they are incorporated into relatively low-cost, medium-powered receivers that just about anyone interested in good sound can afford. The Denon DRA-400 is a good example of a receiver which has benefited from technology first found in higher priced units. This receiver employs crystal-controlled, frequency-synthesized tuning for accuracy and has a five-station preset capability with battery-operated memory backup. Not only does the phono preamplifier section incorporate both moving-magnet and moving-coil inputs (the latter at an input impedance of 100 ohms), but the phono preamp-equalizer section has a direct-coupled input. The power amplifier section employs a non-switching biasing circuit for the elimination of so-called switching and notch distortion at the output stages. These refinements would have been found only on more expensive components just a few years ago. The front panel of the Denon DRA-400 is neatly divided into highly functional upper and lower sections. The upper section contains the power on/off switch, a numeric display of station frequency, a stereo indicator light, a signal-strength LED indicator, up and down tuning buttons, the five preset buttons and their memory switch, program selector pushbuttons, and a large, rotary master-volume control. The signal-strength indicator takes the form of a go-no-go indicator, rather than a signal-strength meter: It lights when the incoming signal strength is deemed adequate and does not light when weaker signals are received-an interesting approach but not very useful. Controls in the lower section are normally covered by a swing-down hinged door, since they are used less frequently than those just described. Behind the door panel are a stereo headphone jack; a pair of speaker selector buttons; bass, treble and balance controls; a three-position monitor/ copy switch; a subsonic filter switch; a stereo/mono switch (associated with FM reception); an MM/MC phono switch, and a loudness on/off switch. The rear panel of the DRA-400 is equipped with the usual 75- and 300-ohm FM antenna terminals, phono and high level input terminals, two pairs of tape in/out jacks, two pairs of color-coded speaker connection terminals, a chassis ground terminal, and a pair of a.c. convenience outlets (one switched, one unswitched). Instead of the usual AM loop stick antenna, a more elaborate, true AM loop antenna is packed with the receiver as a separate item; its two leads must be connected to the appropriate AM and ground terminals on the back of the set. The pivotable loop antenna is best snapped into an antenna holder during receiver installation so the antenna can still be rotated for best AM reception. Since this loop antenna forms part of the input-stage tuned circuit, the owners manual suggests that even if an outdoor AM antenna is used (because of inadequate signal strength), the loop antennas leads should remain connected to their appropriate terminals, in parallel with the outdoor antenna leads. Tuner Measurements Usable mono FM sensitivity fell short of published claims, measuring 16 dBf (3.47 V across 300 ohms). In stereo, sensitivity was limited by muting and stereo thresholds, which were set to 32 dBf (21.9 V). For 50-dB quieting in mono, an input signal strength of 19.5 dBf (5.2 V) was required; for stereo, a signal strength of 42 dBf (69.2 V) was needed. Plots of quieting and distortion (at 1 kHz) versus signal strength are shown in Fig. 1. Signal-to-noise in mono, at 65 dBf of input signal, measured 75 dB as claimed; in stereo it was 72 dB, also exactly as claimed. Harmonic distortion in mono measured 0.17% for a 1-kHz signal, modulating the r.f. carrier by 100%. Total harmonic distortion actually decreased to 0.085% in stereo for the same signal and modulation levels. Distortion in mono and stereo for other audio modulating frequencies is shown in Fig. 2. Although measured distortion was low at high frequencies in stereo and mono, I must point out that these figures were obtained using a bandpass filter with a steep roll-off above 15 kHz (the highest broadcast program frequency). Without the filter, subcarrier products were only some 42 dB below 100% modulation levels.

100% Authentic! All packages are shipped directly from Japan!Condition DescriptionDrive system Direct Drive RPM 33 1/3, 45 rpm Tone arm type AUDIOCRAFT AC-4000MC-S straight type Attached Cartridge AUDIO-TECHNICA AT10G installed (not covered by warranty) Features and Remarks RCA cable included Please Note shipping from Japan. Policy PaymentYou can use various payment methods based on eBay Managed Payments. Import duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyers responsibility.Cancellations & ReturnsCancellation or returns will be accepted only if the item has an obvious problem that was not mentioned in the listing description. If that, please let us know within 3 days you got the item. Buyer is responsible for shipping costs and any charge incurred shipping products back.International BuyersImport duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyers responsibility. Please check with your countrys customs office to determine what these additional costs will be prior to bidding/buying. These charges are normally collected by the delivering freight (shipping) company or when you pick the item up - do not confuse them for additional shipping charges.

Denon DRA 400 Precision Audio Component AM/FM Tuner Stereo AMP Receiver ???? Works. Condition is Used. Shipped with USPS Ground Advantage.

Denon DRA 400 Precision Audio Component AM/FM Tuner Stereo AMP Receiver Used, works - Bought at an estate sale, history unknown Tape Deck Not Included Video available of working FM and Cassette under extra kart parts youtube channel - message for link Below description found online and buyer must confirm accuracy- reference only - Info from gamma electronics - XYZ Manufacturers Specifications FM Tuner Section: Usable Mono Sensitivity: 10.3 dBf. S/N Ratio: Mono, 75 dB; stereo, 72 dB. THD at 1 kHz: Mono, 0.1%; stereo, 0.2%. Capture Ratio: 1.2 dB. Image Rejection: 45 dB. AM Suppression: 60 dB. Stereo Separation, 1 kHz: 50 dB. Frequency Response: 10 Hz to 15 kHz, +0.2,-1.5 dB. AM Tuner Section: Usable Sensitivity: 15 dB. S/N Ratio: 55 dB. Amplifier Section: Power Output: 40 watts per channel, 8 ohms, 20 Hz to 20 kHz (50 watts, 1 kHz, 4 ohms). THD: 0.02%, 8 ohms. Damping Factor: 80, 1 kHz, 8 ohms. Input Sensitivity: MM phono, 2.5 mV; MC phono, 0.25 mV; high level, 150 mV. Maximum Phono Input Level: MM phono, 200 mV; MC phono, 20 mV. Frequency Response: Phono, RIAA 0.5 dB; high level, 20 Hz to 20 kHz, 0.5 dB. S/N Ratio: MM phono, 80 dB; MC phono, 62 dB; high level, 96 dB. Tone Control Range: 10 dB at 50 Hz and 10 kHz. Subsonic Filter Cutoff: 18 Hz, 6 dB per octave. General Specifications: Power Consumption: 130 watts. Dimensions: 17.1 in. (43.4 cm) W x 4.4 in. (11.2 cm) H x 16.1 in. (40.8 cm) D. Weight: 19.8 lbs. (9.0 kg). Price: $399.95. Company Address: 61 Law Dr., Fairfield, N.J. 07006. As so often happens with advances in audio technology, new features are first incorporated in top-of-the-line separate components which are beyond the reach of all but the most affluent of audio enthusiasts. Later on, these features filter down to high-powered, high-priced all-in-one receiv ers, where a larger audience is potentially available. Finally, they are incorporated into relatively low-cost, medium-powered receivers that just about anyone interested in good sound can afford. The Denon DRA-400 is a good example of a receiver which has benefited from technology first found in higher priced units. This receiver employs crystal-controlled, frequency-synthesized tuning for accuracy and has a five-station preset capability with battery-operated memory backup. Not only does the phono preamplifier section incorporate both moving-magnet and moving-coil inputs (the latter at an input impedance of 100 ohms), but the phono preamp-equalizer section has a direct-coupled input. The power amplifier section employs a non-switching biasing circuit for the elimination of so-called switching and notch distortion at the output stages. These refinements would have been found only on more expensive components just a few years ago. The front panel of the Denon DRA-400 is neatly divided into highly functional upper and lower sections. The upper section contains the power on/off switch, a numeric display of station frequency, a stereo indicator light, a signal-strength LED indicator, up and down tuning buttons, the five preset buttons and their memory switch, program selector pushbuttons, and a large, rotary master-volume control. The signal-strength indicator takes the form of a go-no-go indicator, rather than a signal-strength meter: It lights when the incoming signal strength is deemed adequate and does not light when weaker signals are received-an interesting approach but not very useful. Controls in the lower section are normally covered by a swing-down hinged door, since they are used less frequently than those just described. Behind the door panel are a stereo headphone jack; a pair of speaker selector buttons; bass, treble and balance controls; a three-position monitor/ copy switch; a subsonic filter switch; a stereo/mono switch (associated with FM reception); an MM/MC phono switch, and a loudness on/off switch. The rear panel of the DRA-400 is equipped with the usual 75- and 300-ohm FM antenna terminals, phono and high level input terminals, two pairs of tape in/out jacks, two pairs of color-coded speaker connection terminals, a chassis ground terminal, and a pair of a.c. convenience outlets (one switched, one unswitched). Instead of the usual AM loop stick antenna, a more elaborate, true AM loop antenna is packed with the receiver as a separate item; its two leads must be connected to the appropriate AM and ground terminals on the back of the set. The pivotable loop antenna is best snapped into an antenna holder during receiver installation so the antenna can still be rotated for best AM reception. Since this loop antenna forms part of the input-stage tuned circuit, the owners manual suggests that even if an outdoor AM antenna is used (because of inadequate signal strength), the loop antennas leads should remain connected to their appropriate terminals, in parallel with the outdoor antenna leads. Tuner Measurements Usable mono FM sensitivity fell short of published claims, measuring 16 dBf (3.47 V across 300 ohms). In stereo, sensitivity was limited by muting and stereo thresholds, which were set to 32 dBf (21.9 V). For 50-dB quieting in mono, an input signal strength of 19.5 dBf (5.2 V) was required; for stereo, a signal strength of 42 dBf (69.2 V) was needed. Plots of quieting and distortion (at 1 kHz) versus signal strength are shown in Fig. 1. Signal-to-noise in mono, at 65 dBf of input signal, measured 75 dB as claimed; in stereo it was 72 dB, also exactly as claimed. Harmonic distortion in mono measured 0.17% for a 1-kHz signal, modulating the r.f. carrier by 100%. Total harmonic distortion actually decreased to 0.085% in stereo for the same signal and modulation levels. Distortion in mono and stereo for other audio modulating frequencies is shown in Fig. 2. Although measured distortion was low at high frequencies in stereo and mono, I must point out that these figures were obtained using a bandpass filter with a steep roll-off above 15 kHz (the highest broadcast program frequency). Without the filter, subcarrier products were only some 42 dB below 100% modulation levels.

Denon POA-4400A POWER AMPLIFIER / ENDSTUFE + Equalizer. 2 1m xlr chinch vandenhul silberkabel + 25m chinch vandenhul silberkabel . Top Zustand Bei Rckfragen Olaf Hartmann 015738127741 zwischen 16:00 - 20:00 Uhr Da privat verkauf keine Garantie und rcknahme.

This Denon DRA-400 Tuner Amp is a fully functional and tested device that will provide you with high-quality audio. It is designed for desktop use and has six input options, two output options, and two channels. The beige color of the device adds a touch of elegance to your setup. The amplifier is suitable for use with components and will give you the best audio experience. The model of the product is DRA 400, which is known for its reliability and durability. Used in great condition

Denon DRA 400 Precision Audio Component AM/FM Tuner Stereo AMP Receiver ???? Works. Condition is Used. Shipped with USPS Ground Advantage.

Denon DRA 400 Precision Audio Component AM/FM Tuner Stereo AMP Receiver Used, works - Bought at an estate sale, history unknown Tape Deck Not Included Video available of working FM and Cassette under extra kart parts youtube channel - message for link Below description found online and buyer must confirm accuracy- reference only - Info from gamma electronics - XYZ Manufacturers Specifications FM Tuner Section: Usable Mono Sensitivity: 10.3 dBf. S/N Ratio: Mono, 75 dB; stereo, 72 dB. THD at 1 kHz: Mono, 0.1%; stereo, 0.2%. Capture Ratio: 1.2 dB. Image Rejection: 45 dB. AM Suppression: 60 dB. Stereo Separation, 1 kHz: 50 dB. Frequency Response: 10 Hz to 15 kHz, +0.2,-1.5 dB. AM Tuner Section: Usable Sensitivity: 15 dB. S/N Ratio: 55 dB. Amplifier Section: Power Output: 40 watts per channel, 8 ohms, 20 Hz to 20 kHz (50 watts, 1 kHz, 4 ohms). THD: 0.02%, 8 ohms. Damping Factor: 80, 1 kHz, 8 ohms. Input Sensitivity: MM phono, 2.5 mV; MC phono, 0.25 mV; high level, 150 mV. Maximum Phono Input Level: MM phono, 200 mV; MC phono, 20 mV. Frequency Response: Phono, RIAA 0.5 dB; high level, 20 Hz to 20 kHz, 0.5 dB. S/N Ratio: MM phono, 80 dB; MC phono, 62 dB; high level, 96 dB. Tone Control Range: 10 dB at 50 Hz and 10 kHz. Subsonic Filter Cutoff: 18 Hz, 6 dB per octave. General Specifications: Power Consumption: 130 watts. Dimensions: 17.1 in. (43.4 cm) W x 4.4 in. (11.2 cm) H x 16.1 in. (40.8 cm) D. Weight: 19.8 lbs. (9.0 kg). Price: $399.95. Company Address: 61 Law Dr., Fairfield, N.J. 07006. As so often happens with advances in audio technology, new features are first incorporated in top-of-the-line separate components which are beyond the reach of all but the most affluent of audio enthusiasts. Later on, these features filter down to high-powered, high-priced all-in-one receiv ers, where a larger audience is potentially available. Finally, they are incorporated into relatively low-cost, medium-powered receivers that just about anyone interested in good sound can afford. The Denon DRA-400 is a good example of a receiver which has benefited from technology first found in higher priced units. This receiver employs crystal-controlled, frequency-synthesized tuning for accuracy and has a five-station preset capability with battery-operated memory backup. Not only does the phono preamplifier section incorporate both moving-magnet and moving-coil inputs (the latter at an input impedance of 100 ohms), but the phono preamp-equalizer section has a direct-coupled input. The power amplifier section employs a non-switching biasing circuit for the elimination of so-called switching and notch distortion at the output stages. These refinements would have been found only on more expensive components just a few years ago. The front panel of the Denon DRA-400 is neatly divided into highly functional upper and lower sections. The upper section contains the power on/off switch, a numeric display of station frequency, a stereo indicator light, a signal-strength LED indicator, up and down tuning buttons, the five preset buttons and their memory switch, program selector pushbuttons, and a large, rotary master-volume control. The signal-strength indicator takes the form of a go-no-go indicator, rather than a signal-strength meter: It lights when the incoming signal strength is deemed adequate and does not light when weaker signals are received-an interesting approach but not very useful. Controls in the lower section are normally covered by a swing-down hinged door, since they are used less frequently than those just described. Behind the door panel are a stereo headphone jack; a pair of speaker selector buttons; bass, treble and balance controls; a three-position monitor/ copy switch; a subsonic filter switch; a stereo/mono switch (associated with FM reception); an MM/MC phono switch, and a loudness on/off switch. The rear panel of the DRA-400 is equipped with the usual 75- and 300-ohm FM antenna terminals, phono and high level input terminals, two pairs of tape in/out jacks, two pairs of color-coded speaker connection terminals, a chassis ground terminal, and a pair of a.c. convenience outlets (one switched, one unswitched). Instead of the usual AM loop stick antenna, a more elaborate, true AM loop antenna is packed with the receiver as a separate item; its two leads must be connected to the appropriate AM and ground terminals on the back of the set. The pivotable loop antenna is best snapped into an antenna holder during receiver installation so the antenna can still be rotated for best AM reception. Since this loop antenna forms part of the input-stage tuned circuit, the owners manual suggests that even if an outdoor AM antenna is used (because of inadequate signal strength), the loop antennas leads should remain connected to their appropriate terminals, in parallel with the outdoor antenna leads. Tuner Measurements Usable mono FM sensitivity fell short of published claims, measuring 16 dBf (3.47 V across 300 ohms). In stereo, sensitivity was limited by muting and stereo thresholds, which were set to 32 dBf (21.9 V). For 50-dB quieting in mono, an input signal strength of 19.5 dBf (5.2 V) was required; for stereo, a signal strength of 42 dBf (69.2 V) was needed. Plots of quieting and distortion (at 1 kHz) versus signal strength are shown in Fig. 1. Signal-to-noise in mono, at 65 dBf of input signal, measured 75 dB as claimed; in stereo it was 72 dB, also exactly as claimed. Harmonic distortion in mono measured 0.17% for a 1-kHz signal, modulating the r.f. carrier by 100%. Total harmonic distortion actually decreased to 0.085% in stereo for the same signal and modulation levels. Distortion in mono and stereo for other audio modulating frequencies is shown in Fig. 2. Although measured distortion was low at high frequencies in stereo and mono, I must point out that these figures were obtained using a bandpass filter with a steep roll-off above 15 kHz (the highest broadcast program frequency). Without the filter, subcarrier products were only some 42 dB below 100% modulation levels.

Cellule occasion testéePossibilité de vous fournir le saphir qui va avec neuf dans son emballage d originehttps://www.ebay.fr/itm/saphir-diamant-pointe-de-lecture-Orion-806/293037708097?hash=item443a689341:g:ZdYAAOSwhZ9a8rNeJe peux vous renseigner si elle peut se monter sur votre platineAutre pièces disponibles neuf ou occasion, me contacterA partir de la référence de la platine vinyle je peux éventuellement vous proposer le saphir, diamant, pointe de lecture ou cellule que vous cherchez en menvoyant une photo précise de ce que vous souhaitez afin déviter les erreursLe saphir nest pas compris dans loffre, il est la uniquement pour montrer quel est le saphir ou diamant qui ce monte dessusPhoto contractuelle

A/V-Receiver DENON AVR-3311 mit 7-Kanal-Endstufe, Neupreis 1.400 Euro. Toller Sound zum kleinen Preis!

Denon DRA-400 Tuner Amp FULLY WORKING, TESTED.

Denon DP-400 (WHITE) Semi-Automatic Analog Turntable with Speed Auto Sensor | Specially Designed Curved Tonearm | Supports 33 1/3. 45, 78 RPM (Vintage) Speeds | Modern Looks, Superior Audio Battery life not tested.     Item is sold as is! Comes with only what is pictured in the photos.  Features {{itemfeatures}} Details {{itemdetails}} {{marketing_message_heading_1}} {{marketing_message_body_1}} {{marketing_message_heading_2}} {{marketing_message_body_2}} {{marketing_message_heading_3}} {{marketing_message_body_3}}

Denon Mono Endstufe POA-4400 A HiFi Monoblock Poa 4400a gebraucht, mit geringen Gebrauchsspuren, voll funktionsfhig.

Denon Mono Endstufe POA-4400 A befindet sich in einem dem Alter entsprechenden guten Zustand. Da Privatverkauf ohne Garantie und Rcknahme.

Denon Mono Endstufe POA-4400 A befindet sich in einem dem Alter entsprechenden guten Zustand. Da Privatverkauf ohne Garantie und Rcknahme.

Denon DRA 400 Precision Audio Component AM/FM Tuner Stereo AMP Receiver Used, works - Bought at an estate sale, history unknown Tape Deck Not Included Video available of working FM and Cassette under extra kart parts youtube channel - message for link Below description found online and buyer must confirm accuracy- reference only - Info from gamma electronics - XYZ Manufacturers Specifications FM Tuner Section: Usable Mono Sensitivity: 10.3 dBf. S/N Ratio: Mono, 75 dB; stereo, 72 dB. THD at 1 kHz: Mono, 0.1%; stereo, 0.2%. Capture Ratio: 1.2 dB. Image Rejection: 45 dB. AM Suppression: 60 dB. Stereo Separation, 1 kHz: 50 dB. Frequency Response: 10 Hz to 15 kHz, +0.2,-1.5 dB. AM Tuner Section: Usable Sensitivity: 15 dB. S/N Ratio: 55 dB. Amplifier Section: Power Output: 40 watts per channel, 8 ohms, 20 Hz to 20 kHz (50 watts, 1 kHz, 4 ohms). THD: 0.02%, 8 ohms. Damping Factor: 80, 1 kHz, 8 ohms. Input Sensitivity: MM phono, 2.5 mV; MC phono, 0.25 mV; high level, 150 mV. Maximum Phono Input Level: MM phono, 200 mV; MC phono, 20 mV. Frequency Response: Phono, RIAA 0.5 dB; high level, 20 Hz to 20 kHz, 0.5 dB. S/N Ratio: MM phono, 80 dB; MC phono, 62 dB; high level, 96 dB. Tone Control Range: 10 dB at 50 Hz and 10 kHz. Subsonic Filter Cutoff: 18 Hz, 6 dB per octave. General Specifications: Power Consumption: 130 watts. Dimensions: 17.1 in. (43.4 cm) W x 4.4 in. (11.2 cm) H x 16.1 in. (40.8 cm) D. Weight: 19.8 lbs. (9.0 kg). Price: $399.95. Company Address: 61 Law Dr., Fairfield, N.J. 07006. As so often happens with advances in audio technology, new features are first incorporated in top-of-the-line separate components which are beyond the reach of all but the most affluent of audio enthusiasts. Later on, these features filter down to high-powered, high-priced all-in-one receiv ers, where a larger audience is potentially available. Finally, they are incorporated into relatively low-cost, medium-powered receivers that just about anyone interested in good sound can afford. The Denon DRA-400 is a good example of a receiver which has benefited from technology first found in higher priced units. This receiver employs crystal-controlled, frequency-synthesized tuning for accuracy and has a five-station preset capability with battery-operated memory backup. Not only does the phono preamplifier section incorporate both moving-magnet and moving-coil inputs (the latter at an input impedance of 100 ohms), but the phono preamp-equalizer section has a direct-coupled input. The power amplifier section employs a non-switching biasing circuit for the elimination of so-called switching and notch distortion at the output stages. These refinements would have been found only on more expensive components just a few years ago. The front panel of the Denon DRA-400 is neatly divided into highly functional upper and lower sections. The upper section contains the power on/off switch, a numeric display of station frequency, a stereo indicator light, a signal-strength LED indicator, up and down tuning buttons, the five preset buttons and their memory switch, program selector pushbuttons, and a large, rotary master-volume control. The signal-strength indicator takes the form of a go-no-go indicator, rather than a signal-strength meter: It lights when the incoming signal strength is deemed adequate and does not light when weaker signals are received-an interesting approach but not very useful. Controls in the lower section are normally covered by a swing-down hinged door, since they are used less frequently than those just described. Behind the door panel are a stereo headphone jack; a pair of speaker selector buttons; bass, treble and balance controls; a three-position monitor/ copy switch; a subsonic filter switch; a stereo/mono switch (associated with FM reception); an MM/MC phono switch, and a loudness on/off switch. The rear panel of the DRA-400 is equipped with the usual 75- and 300-ohm FM antenna terminals, phono and high level input terminals, two pairs of tape in/out jacks, two pairs of color-coded speaker connection terminals, a chassis ground terminal, and a pair of a.c. convenience outlets (one switched, one unswitched). Instead of the usual AM loop stick antenna, a more elaborate, true AM loop antenna is packed with the receiver as a separate item; its two leads must be connected to the appropriate AM and ground terminals on the back of the set. The pivotable loop antenna is best snapped into an antenna holder during receiver installation so the antenna can still be rotated for best AM reception. Since this loop antenna forms part of the input-stage tuned circuit, the owners manual suggests that even if an outdoor AM antenna is used (because of inadequate signal strength), the loop antennas leads should remain connected to their appropriate terminals, in parallel with the outdoor antenna leads. Tuner Measurements Usable mono FM sensitivity fell short of published claims, measuring 16 dBf (3.47 V across 300 ohms). In stereo, sensitivity was limited by muting and stereo thresholds, which were set to 32 dBf (21.9 V). For 50-dB quieting in mono, an input signal strength of 19.5 dBf (5.2 V) was required; for stereo, a signal strength of 42 dBf (69.2 V) was needed. Plots of quieting and distortion (at 1 kHz) versus signal strength are shown in Fig. 1. Signal-to-noise in mono, at 65 dBf of input signal, measured 75 dB as claimed; in stereo it was 72 dB, also exactly as claimed. Harmonic distortion in mono measured 0.17% for a 1-kHz signal, modulating the r.f. carrier by 100%. Total harmonic distortion actually decreased to 0.085% in stereo for the same signal and modulation levels. Distortion in mono and stereo for other audio modulating frequencies is shown in Fig. 2. Although measured distortion was low at high frequencies in stereo and mono, I must point out that these figures were obtained using a bandpass filter with a steep roll-off above 15 kHz (the highest broadcast program frequency). Without the filter, subcarrier products were only some 42 dB below 100% modulation levels.

DENON DP400 HI FI TURNTABLE + ORTOFON 2M BLUE UPGRADE Like Brand New Perfect. condition. Very lightly used. All original boxing included.

Denon Mono Endstufe POA-4400 A befindet sich in einem dem Alter entsprechenden guten Zustand. Da Privatverkauf ohne Garantie und Rcknahme.

Denon DRA 400 Precision Audio Component AM/FM Tuner Stereo AMP Receiver ???? Works. Condition is Used. Shipped with USPS Ground Advantage.

Denon DRM-400 Stereo Kassettendeck , funktionstchtig. Das Gert ist retestet und voll funktionsfhig. Es ist optisch bis auf Flecken auf der Oberseite, die mglicherweise noch gereinigt werden knnen in gutem Zustand.

Denon DP-400 Stereo Turntable - Piano Black Item Specifics: Part Number: DP400BKEM Color: Piano Black Condition: Open Box-- New and unused; opened; inner contents undisturbed; all included items shown in photos and untested unless otherwise noted; distressed packaging; labels removed from box exterior Features: Model: DP-400 Plays 33.3, 45 & 78 RPM records Built-in Phono Equalizer Auto speed sensor Auto-life & return tonearm Removable dust cover Cargo Largo is not sponsored by or affiliated with the brand associated with the product being sold. This item cannot be shipped out of the United States! Cargo Largo is not sponsored by or affiliated with the brand associated with the product being sold. Contact Seller If you have any questions, please use the “Contact Seller” link in the upper right section of the listing.Our business hours are 8:00 AM - 3:30 PM Monday-Friday (Central Time).Sales completed and emails received after normal business hours may be handled the next business day. Shipping Policy We ONLY ship within the lower 48 United States.We ONLY ship to the address selected by the customer at checkout.Buyers MAY NOT arrange their own shipping.ALL orders with total value of $250 or more WILL require a delivery signature.For this item, we DO NOT offer combined shipping with other listings. Location We offer local pickup for all our eBay auction items. To request local pickup for items you have won, please send us a message asking for “pick up” and we will send you an eBay invoice with your total.All local pickup orders MUST be paid within 8 DAYS after the listing ended per eBay policy. The payment total will include Missouri sales tax  AND a $4 handling fee per item.Non-Missouri residents will need to pay IN PERSON (credit/debit cards only) within 4 days after the listing ended.Buy It Now items are NOT eligible for local pickup.Paid items must be picked up within 10 DAYS after the end of the listing. If not, your order will be cancelled and refunded.Social distancing policies WILL be enforced during pickups. Local Pickup Location 7460 Stadium Drive Kansas City, MO 64129 Pickup Hours SUNDAY MONDAY TUESDAY WEDNESDAY THURSDAY FRIDAY SATURDAY CLOSED 11am-6pm 7:30am-4pm CLOSED 7:30am-4pm 7:30am-6pm CLOSED Return Policy We are not an authorized dealer of this product and any warranty included with the product may not be honored by the manufacturer. If you believe that the item purchased from us does not match the item description, or if your item was damaged during transit, please contact us to discuss return and refund options. In order to initiate the refund process, buyer must contact us within 30 Days of receipt of item. All returns will require a return authorization. Please note that we will only pay return shipping if our listing does not accurately reflect the specifications or condition of the item received. If you wish to return an item for any other reason, we will accept a return on MOST items, provided that the item is returned to us in the same condition and within 30 Days. This applies to both the item and retail packaging. Buyer will be responsible for both original and return shipping charges Seller will initiate this transaction and refund the buyer once the item has been received AND agreed to the mutual cancellation. We DO NOT accept any returns on swimsuits, undergarments, stockings, lingerie, or any item marked AS IS for any reason other than a grievous error in the listing. Please bid accordingly on all items listed AS IS. Payments Cargo Largo requires payment within eight (8) days. (Please note that this is real-time, beginning when the auction ends.) If payment has still not been received by the eighth (8th) day after the end of the auction, Cargo Largo will relist the item. Most states require the collection of SALES TAX on online sales by remote sellers. We will abide by all local, state and federal tax codes and buyer should check their state and locality for tax liability. Residents of Missouri and all buyers who pick their item(s) up locally are required to pay Missouri sales tax on all items. Sell Smarter with Kyozou.Inventory and Ecommerce Management

Denon DRA 400 Precision Audio Component AM/FM Tuner Stereo AMP Receiver Used, works - Bought at an estate sale, history unknown Tape Deck Not Included Video available of working FM and Cassette under extra kart parts youtube channel - message for link Below description found online and buyer must confirm accuracy- reference only - Info from gamma electronics - XYZ Manufacturers Specifications FM Tuner Section: Usable Mono Sensitivity: 10.3 dBf. S/N Ratio: Mono, 75 dB; stereo, 72 dB. THD at 1 kHz: Mono, 0.1%; stereo, 0.2%. Capture Ratio: 1.2 dB. Image Rejection: 45 dB. AM Suppression: 60 dB. Stereo Separation, 1 kHz: 50 dB. Frequency Response: 10 Hz to 15 kHz, +0.2,-1.5 dB. AM Tuner Section: Usable Sensitivity: 15 dB. S/N Ratio: 55 dB. Amplifier Section: Power Output: 40 watts per channel, 8 ohms, 20 Hz to 20 kHz (50 watts, 1 kHz, 4 ohms). THD: 0.02%, 8 ohms. Damping Factor: 80, 1 kHz, 8 ohms. Input Sensitivity: MM phono, 2.5 mV; MC phono, 0.25 mV; high level, 150 mV. Maximum Phono Input Level: MM phono, 200 mV; MC phono, 20 mV. Frequency Response: Phono, RIAA 0.5 dB; high level, 20 Hz to 20 kHz, 0.5 dB. S/N Ratio: MM phono, 80 dB; MC phono, 62 dB; high level, 96 dB. Tone Control Range: 10 dB at 50 Hz and 10 kHz. Subsonic Filter Cutoff: 18 Hz, 6 dB per octave. General Specifications: Power Consumption: 130 watts. Dimensions: 17.1 in. (43.4 cm) W x 4.4 in. (11.2 cm) H x 16.1 in. (40.8 cm) D. Weight: 19.8 lbs. (9.0 kg). Price: $399.95. Company Address: 61 Law Dr., Fairfield, N.J. 07006. As so often happens with advances in audio technology, new features are first incorporated in top-of-the-line separate components which are beyond the reach of all but the most affluent of audio enthusiasts. Later on, these features filter down to high-powered, high-priced all-in-one receiv ers, where a larger audience is potentially available. Finally, they are incorporated into relatively low-cost, medium-powered receivers that just about anyone interested in good sound can afford. The Denon DRA-400 is a good example of a receiver which has benefited from technology first found in higher priced units. This receiver employs crystal-controlled, frequency-synthesized tuning for accuracy and has a five-station preset capability with battery-operated memory backup. Not only does the phono preamplifier section incorporate both moving-magnet and moving-coil inputs (the latter at an input impedance of 100 ohms), but the phono preamp-equalizer section has a direct-coupled input. The power amplifier section employs a non-switching biasing circuit for the elimination of so-called switching and notch distortion at the output stages. These refinements would have been found only on more expensive components just a few years ago. The front panel of the Denon DRA-400 is neatly divided into highly functional upper and lower sections. The upper section contains the power on/off switch, a numeric display of station frequency, a stereo indicator light, a signal-strength LED indicator, up and down tuning buttons, the five preset buttons and their memory switch, program selector pushbuttons, and a large, rotary master-volume control. The signal-strength indicator takes the form of a go-no-go indicator, rather than a signal-strength meter: It lights when the incoming signal strength is deemed adequate and does not light when weaker signals are received-an interesting approach but not very useful. Controls in the lower section are normally covered by a swing-down hinged door, since they are used less frequently than those just described. Behind the door panel are a stereo headphone jack; a pair of speaker selector buttons; bass, treble and balance controls; a three-position monitor/ copy switch; a subsonic filter switch; a stereo/mono switch (associated with FM reception); an MM/MC phono switch, and a loudness on/off switch. The rear panel of the DRA-400 is equipped with the usual 75- and 300-ohm FM antenna terminals, phono and high level input terminals, two pairs of tape in/out jacks, two pairs of color-coded speaker connection terminals, a chassis ground terminal, and a pair of a.c. convenience outlets (one switched, one unswitched). Instead of the usual AM loop stick antenna, a more elaborate, true AM loop antenna is packed with the receiver as a separate item; its two leads must be connected to the appropriate AM and ground terminals on the back of the set. The pivotable loop antenna is best snapped into an antenna holder during receiver installation so the antenna can still be rotated for best AM reception. Since this loop antenna forms part of the input-stage tuned circuit, the owners manual suggests that even if an outdoor AM antenna is used (because of inadequate signal strength), the loop antennas leads should remain connected to their appropriate terminals, in parallel with the outdoor antenna leads. Tuner Measurements Usable mono FM sensitivity fell short of published claims, measuring 16 dBf (3.47 V across 300 ohms). In stereo, sensitivity was limited by muting and stereo thresholds, which were set to 32 dBf (21.9 V). For 50-dB quieting in mono, an input signal strength of 19.5 dBf (5.2 V) was required; for stereo, a signal strength of 42 dBf (69.2 V) was needed. Plots of quieting and distortion (at 1 kHz) versus signal strength are shown in Fig. 1. Signal-to-noise in mono, at 65 dBf of input signal, measured 75 dB as claimed; in stereo it was 72 dB, also exactly as claimed. Harmonic distortion in mono measured 0.17% for a 1-kHz signal, modulating the r.f. carrier by 100%. Total harmonic distortion actually decreased to 0.085% in stereo for the same signal and modulation levels. Distortion in mono and stereo for other audio modulating frequencies is shown in Fig. 2. Although measured distortion was low at high frequencies in stereo and mono, I must point out that these figures were obtained using a bandpass filter with a steep roll-off above 15 kHz (the highest broadcast program frequency). Without the filter, subcarrier products were only some 42 dB below 100% modulation levels.