good condition male to female 34 XLR cable i used for my Center Channel

AudioQuest Red River XLR Interconnect Cables - 1 Meter Pair - New - Open Box Authorized Dealer Since 1980 - Factory Warranty Applies Cable is New. Boxes are rough, torn or otherwise distressed. About Audioquest Factory Authorized Open Box Products: These items have been opened for one reason or another. Product Condition is “As-New” and includes the Audioquest warranty stated below. Most cable and accessory items have their original boxes and packaging. Sometimes boxes may be torn or show wear. Cables that dont have their boxes will come in a sealed plastic bag. Niagara series products will always have their original boxes, packaging and owners manual. Audioquest Product Warranty for the United States:AudioQuest products are manufactured to exacting standards and are subject to rigorous quality control.However, if a manufacturing defect is found in any cable, connector, or factory assembled product, AudioQuest’s non-transferable original-owner limited lifetime warranty has you covered for any cable, connector, or factory assembled product purchased through an authorized AudioQuest US dealer.At its option, AudioQuest will repair or replace any defective cable, connector, or factory assembled product that has not been abused, for the lifetime of the product. Proof of original purchase is required.For all other products, AudioQuest provides a limited, non-transferable, one-year warranty to original owners who purchased their product through an authorized AudioQuest dealer in the United States. At its option, AudioQuest will repair or replace any defective product that has not been abused, for up to one year from the original date of purchase. Proof of original purchase is required.Cables not terminated by AudioQuest that require service may be returned to AudioQuest with prior authorization and repaired for a fee.This warranty is not an upgrade program for AudioQuest HDMI cables that were designed to meet previous generations of HDMI specifications. Current AudioQuest models are designed to meet HDMI 2.0 (18Gbps) or HDMI 2.1 (48Gbps).All generations of HDMI cable will provide some, but not all, of the features made possible by HDMI 2.0 and 2.1. All generations of HDMI cable are backwards compatible—they provide all the capabilities of previous generations.To experience the audio/video benefits made possible by the latest HDMI 2.1 hardware, an HDMI cable must meet HDMI specifications, specifically an FRL-enabled bandwidth of 48Gbps.This warranty is valid in the United States only. For warranty policies in other countries, please contact your local dealer or distributor.Limitations and ConditionsThis warranty is subject to the following limitations and conditions:The unit will not be covered under the warranty if:• It has been altered or modified in any way.• It has been damaged due to misuse,negligence,accident or improper operation.• It has been subjected to water damage, or extremes of humidity or temperature.• It has been purchased from an unauthorized dealer, or unauthorized repair or service has beenperformed. For repairs and returns:• A request for a Return Merchandise Authorization (RMA) number must be made in writing or via phone to AudioQuest.• A return address and phone number must be included.• Returned product must be accompanied by the RMA number, a written description of the defect orissue, and a photocopy of the original purchase receipt.• Customer is responsible for paying shipping charges to AudioQuest.• If the product is found to be out of warranty, as in the conditions specified above, the customer will begiven the option to pay for the repairs or replacement, or to have the unit returned to them.Limited to original purchaser:• This Warranty is for the sole benefit of the original purchaser and shall not be transferred to a subsequent purchaser of the product. Warranty Outside the USA, Netherlands, Germany or the UKAudioQuest has authorized distributors in many countries of the world. In each country, the authorized distributor or dealer thereof has accepted the responsibility for warranty of products sold in their respective countries. Warranty service should normally be obtained from the authorized distributor or dealer from whom you purchased your product. In the unlikely event of service required beyond the capability of the distributor, AudioQuest will fulfill the conditions of the warranty. Such product must be returned at the owner’s expense to AudioQuest, together with a photocopy of the bill of sale for that product, a detailed description of the problem, and any information necessary for return shipment.AudioQuest makes no other express warranty of any kind whatsoever. All implied warranties, including warranties of merchantability and fitness for a particular purpose, exceeding the specific provisions of this warranty are hereby disclaimed and excluded from this warranty.No representative or other person is authorized to assume for AudioQuest any liability except as stated in this warranty. ©2022 AudioQuest

VERY GOOD PREOWNED CONDITION.

New 1m AudioQuest Red River XLR Analogue Audio Interconnect 2 XLR to 2 XLRThis listing is for a New 1m AudioQuest Red River XLR Stereo Analogue Audio Interconnect 2 XLR OFHC (Oxygen-Free High-Conductivity) copper.Solid Perfect-Surface Copper Conductors (PSC) :Strand interaction is the single greatest cause of distortion in a cable. Semi-Solid Concentric Packed Conductors avoid many strand-interaction distortion mechanisms. Solid-core conductors offer a complete and compelling solution to this problem.Conductor metal quality is critical for the best cable performance. The conductor surface is the only area of the conductor with 100% current density at all frequencies. The smoothness of the conductor surface is imperative because the surface is a guide rail for the entire energy envelope. The best copper and silver conductor metals have fewer grain boundaries and low oxygen content for low distortion and high performance.Perfect-Surface Copper has an astonishingly smooth and pure surface. Proprietary metal-processing technology protects the wire’s surface at every stage of drawing and fabrication. When high-purity low-oxide copper is kept as soft, pure and smooth as possible, it becomes a wonderfully low-distortion conductor. For over 30 years AudioQuest has pioneered the use of superior metals; yet even we were surprised by this huge leap in performance. PSC clearly outperforms previous AQ metals that cost over ten times as much. Electrical and magnetic interaction between strands in a conventional cable is the greatest source of distortion, often causing a somewhat dirty, harsh sound. Solid conductors are fundamental toward achieving Red Riverss very clean sound.Nitrogen-Injected Hard-Cell Foam Insulation :Insulation is necessary to keep the positive and negative conductors separate and to give stability to cable geometry. Insulation is also a dielectric because it is inside the conductors magnetic field. Dielectrics absorb energy, which after a delay is then released in the signal, causing smearing and distortion. Better insulation reduces distortion by absorbing less energy.Red River utilises Nitrogen-Injected Hard-Cell Foam insulation and is also used exclusively in most of AudioQuest’s video and digital audio cables. Similar to Foamed-PE, it is nitrogen-injected to create air pockets. ‘Hard’ foam is used because the stiffness of the material allows the conductors in the cable to maintain the same relationship with each other along the full length of the cable, thus ensuring that the characteristic impedance of the cable is consistent.Metal-Layer Noise-Dissipation System (NDS) :100% shield coverage is easy. Preventing captured RF Interference from modulating the equipment’s ground reference requires AQ’s Noise-Dissipation System. Noise-Dissipation System prevents a significant amount of RFI from reaching the equipment’s ground plane.AudioQuest’s Noise-Dissipation System (NDS) offers a compelling solution to this challenge by using metal-only or alternating layers of metal and carbon-loaded synthetics to effectively “shield the shield,” absorbing and reflecting the Radio Frequency (RF) energy before it reaches the layer attached to the ground.Red River ultilises the Metal-Layer Noise-Dissipation System (NDS) to prevent most RFI from reaching the equipment’s ground plane.Triple-Balanced Geometry :Geometry is the physical relationship of the conductors to one another within a cable and determines a cable’s most basic electrical values (capacitance and inductance). Different cable applications have different/specialized geometry requirements, and so these applications do not merely follow a ‘one size fits all’ approach. Better geometry leads to lower levels of distortion.The three conductors in “Triple-Balanced” Red River cables ensure that whether prepared with RCA or XLR plugs, the positive and negative signals have equally low-distortion conducting paths. The 100% coverage shield is never used as an inferior conductor.DirectionalityAudioQuest’s understanding of conductor directionality and its effect on audio performance has steadily evolved, growing stronger and more complete. All audio cables are directional. The correct direction is determined by the arrows on the plugs or cable parts.Cold-Welded Gold-Plated Plugs :AudioQuest specifies materials and designs each of its own connectors from the ground up, resulting in the long-lasting quality and exceptional performance you deserve. These components are crucial to the overall performance of a cable.To provide the best possible performance for each application, AudioQuest designs each of its connectors from the ground up. These components are crucial to the overall performance of the cable. Painstaking care is taken to evaluate the highest quality materials and design for every application.AudioQuest pays special attention to the plating it uses over its connectors’ carefully crafted base metals. Wherever possible, gold connectors are plated directly over the copper, with no destructive intermediate layer of nickel or alloy, while all silver-plated connectors are Direct-Silver plated.AudioQuest has incorporated Cold-Weld connection technology into most of their interconnects and all prepared speaker cables..Joining conductors to plugs requires every bit as much care and precision as any other aspect of cable manufacture. AudioQuests Cold-Weld System uses several tons of pressure to make a near-perfect connection that ensures that the structural integrity of the conductor and plug is kept completely intact, all without the damaging effect of heat. Cold-Welding avoids the introduction of heat and extra materials like solder, which change the character of the wire at the point of termination.This plug design allows for a connection devoid of solder, which is a common source of distortion. Because the ground shells are stamped instead of machined, the metal can be chosen for low distortion instead of machinability.Specification :Metal: Solid Long-Grain CopperGeometry: Triple Balanced (Separate Ground-Reference Conductor)Dielectric: Nitrogen-Injected Hard-Cell FoamNoise-Dissipation System: Metal-Layer NDSJacket Colour: Black/Red BraidTermination: Cold-Welded, Gold-PlatedTERMSPlease bid with confidence, the item is exactly as described. We are authorised dealers for all new items that we sell.Guarantees & Warranties: Brand New products are covered by their respective UK and European warranties, details of which are included with the product. Any Used / Repaired / B-Stock items are sold “As Seen” without warranty unless stated otherwise in the listingReturns:Most Buy It Now purchases are protected by the Distance Selling Regulations. To cancel a Contract, you must inform us in writing, and we will provide return instructions. You must return the products to us at your own cost and risk. You will not have any right to cancel a Contract for the supply of products that have been customised for you, such as pre-cut or terminated speaker cables. This provision does not affect your statutory rights. We cannot accept returns for Ex Display / Repaired / B-Stock or items sold by auction unless the item was not as described in the listing. The buyer must contact us within 3 days of receiving the item to initiate a return. The buyer is responsible for return shipping charges.Payment:We ask that payment is made within 3 days.Shipping:All goods purchased are securely and safely packaged for transit. The cost of Packaging materials (e.g. Jiffy Bags, Bubble Wrap etc) is included in the P&P charge. Items will normally be sent within 3 working days of receipt of cleared payment.Stock:Most items are either in stock with us or our suppliers and available for dispatch within 3 days. Occasionally, an item may be awaiting stock and in these instances we will contact you to confirm you are happy to wait for the item. If availability is key for you, we recommend you check an item is in stock before placing your order.Feedback:We always reciprocate feedback. Please contact us through the eBay system if there is a problem.Images:We often use library photos on our auctions for illustrative purposes only – we are not responsible for colour variances or style updates - you will receive the model and specification stated on the auction.All product serial numbers of items sold on eBay are logged for our mutual protection.Thank you for looking at our listing, please do not hesitate to contact us should you have any questions. Please contact us through the eBay system. Regrettably, we only sell within the UK at this time so do not ask us to ship to other destinations

New 1.5m AudioQuest Red River RCA Analogue Audio Interconnect 2 RCA to 2 RCAThis listing is for a New 1.5m AudioQuest Red River RCA Stereo Analogue Audio Interconnect 2 RCA to 2 RCA. Normally £229Red River’s solid Long-Grain Copper allows a smoother and clearer sound than cables using regular OFHC (Oxygen-Free High-Conductivity) copper.Solid Perfect-Surface Copper Conductors (PSC) :Strand interaction is the single greatest cause of distortion in a cable. Semi-Solid Concentric Packed Conductors avoid many strand-interaction distortion mechanisms. Solid-core conductors offer a complete and compelling solution to this problem.Conductor metal quality is critical for the best cable performance. The conductor surface is the only area of the conductor with 100% current density at all frequencies. The smoothness of the conductor surface is imperative because the surface is a guide rail for the entire energy envelope. The best copper and silver conductor metals have fewer grain boundaries and low oxygen content for low distortion and high performance.Perfect-Surface Copper has an astonishingly smooth and pure surface. Proprietary metal-processing technology protects the wire’s surface at every stage of drawing and fabrication. When high-purity low-oxide copper is kept as soft, pure and smooth as possible, it becomes a wonderfully low-distortion conductor. For over 30 years AudioQuest has pioneered the use of superior metals; yet even we were surprised by this huge leap in performance. PSC clearly outperforms previous AQ metals that cost over ten times as much. Electrical and magnetic interaction between strands in a conventional cable is the greatest source of distortion, often causing a somewhat dirty, harsh sound. Solid conductors are fundamental toward achieving Red Riverss very clean sound.Nitrogen-Injected Hard-Cell Foam Insulation :Insulation is necessary to keep the positive and negative conductors separate and to give stability to cable geometry. Insulation is also a dielectric because it is inside the conductors magnetic field. Dielectrics absorb energy, which after a delay is then released in the signal, causing smearing and distortion. Better insulation reduces distortion by absorbing less energy.Red River utilises Nitrogen-Injected Hard-Cell Foam insulation and is also used exclusively in most of AudioQuest’s video and digital audio cables. Similar to Foamed-PE, it is nitrogen-injected to create air pockets. ‘Hard’ foam is used because the stiffness of the material allows the conductors in the cable to maintain the same relationship with each other along the full length of the cable, thus ensuring that the characteristic impedance of the cable is consistent.Metal-Layer Noise-Dissipation System (NDS) :100% shield coverage is easy. Preventing captured RF Interference from modulating the equipment’s ground reference requires AQ’s Noise-Dissipation System. Noise-Dissipation System prevents a significant amount of RFI from reaching the equipment’s ground plane.AudioQuest’s Noise-Dissipation System (NDS) offers a compelling solution to this challenge by using metal-only or alternating layers of metal and carbon-loaded synthetics to effectively “shield the shield,” absorbing and reflecting the Radio Frequency (RF) energy before it reaches the layer attached to the ground.Red River ultilises the Metal-Layer Noise-Dissipation System (NDS) to prevent most RFI from reaching the equipment’s ground plane.Triple-Balanced Geometry :Geometry is the physical relationship of the conductors to one another within a cable and determines a cable’s most basic electrical values (capacitance and inductance). Different cable applications have different/specialized geometry requirements, and so these applications do not merely follow a ‘one size fits all’ approach. Better geometry leads to lower levels of distortion.The three conductors in “Triple-Balanced” Red River cables ensure that whether prepared with RCA or XLR plugs, the positive and negative signals have equally low-distortion conducting paths. The 100% coverage shield is never used as an inferior conductor.DirectionalityAudioQuest’s understanding of conductor directionality and its effect on audio performance has steadily evolved, growing stronger and more complete. All audio cables are directional. The correct direction is determined by the arrows on the plugs or cable parts.Cold-Welded Gold-Plated Plugs :AudioQuest specifies materials and designs each of its own connectors from the ground up, resulting in the long-lasting quality and exceptional performance you deserve. These components are crucial to the overall performance of a cable.To provide the best possible performance for each application, AudioQuest designs each of its connectors from the ground up. These components are crucial to the overall performance of the cable. Painstaking care is taken to evaluate the highest quality materials and design for every application.AudioQuest pays special attention to the plating it uses over its connectors’ carefully crafted base metals. Wherever possible, gold connectors are plated directly over the copper, with no destructive intermediate layer of nickel or alloy, while all silver-plated connectors are Direct-Silver plated.AudioQuest has incorporated Cold-Weld connection technology into most of their interconnects and all prepared speaker cables..Joining conductors to plugs requires every bit as much care and precision as any other aspect of cable manufacture. AudioQuests Cold-Weld System uses several tons of pressure to make a near-perfect connection that ensures that the structural integrity of the conductor and plug is kept completely intact, all without the damaging effect of heat. Cold-Welding avoids the introduction of heat and extra materials like solder, which change the character of the wire at the point of termination.This plug design allows for a connection devoid of solder, which is a common source of distortion. Because the ground shells are stamped instead of machined, the metal can be chosen for low distortion instead of machinability.Specification :Metal: Solid Long-Grain CopperGeometry: Triple Balanced (Separate Ground-Reference Conductor)Dielectric: Nitrogen-Injected Hard-Cell FoamNoise-Dissipation System: Metal-Layer NDSJacket Colour: Black/Red BraidTermination: Cold-Welded, Gold-PlatedTERMSPlease bid with confidence, the item is exactly as described. We are authorised dealers for all new items that we sell.Guarantees & Warranties: Brand New products are covered by their respective UK and European warranties, details of which are included with the product. Any Used / Repaired / B-Stock items are sold “As Seen” without warranty unless stated otherwise in the listingReturns:Most Buy It Now purchases are protected by the Distance Selling Regulations. To cancel a Contract, you must inform us in writing, and we will provide return instructions. You must return the products to us at your own cost and risk. You will not have any right to cancel a Contract for the supply of products that have been customised for you, such as pre-cut or terminated speaker cables. This provision does not affect your statutory rights. We cannot accept returns for Ex Display / Repaired / B-Stock or items sold by auction unless the item was not as described in the listing. The buyer must contact us within 3 days of receiving the item to initiate a return. The buyer is responsible for return shipping charges.Payment:We ask that payment is made within 3 days.Shipping:All goods purchased are securely and safely packaged for transit. The cost of Packaging materials (e.g. Jiffy Bags, Bubble Wrap etc) is included in the P&P charge. Items will normally be sent within 3 working days of receipt of cleared payment.Stock:Most items are either in stock with us or our suppliers and available for dispatch within 3 days. Occasionally, an item may be awaiting stock and in these instances we will contact you to confirm you are happy to wait for the item. If availability is key for you, we recommend you check an item is in stock before placing your order.Feedback:We always reciprocate feedback. Please contact us through the eBay system if there is a problem.Images:We often use library photos on our auctions for illustrative purposes only – we are not responsible for colour variances or style updates - you will receive the model and specification stated on the auction.All product serial numbers of items sold on eBay are logged for our mutual protection.Thank you for looking at our listing, please do not hesitate to contact us should you have any questions. Please contact us through the eBay system. Regrettably, we only sell within the UK at this time so do not ask us to ship to other destinations

New 1m AudioQuest Red River XLR Analogue Audio Interconnect 2 XLR to 2 XLRThis listing is for a New 1m AudioQuest Red River XLR Stereo Analogue Audio Interconnect 2 XLR OFHC (Oxygen-Free High-Conductivity) copper.Solid Perfect-Surface Copper Conductors (PSC) :Strand interaction is the single greatest cause of distortion in a cable. Semi-Solid Concentric Packed Conductors avoid many strand-interaction distortion mechanisms. Solid-core conductors offer a complete and compelling solution to this problem.Conductor metal quality is critical for the best cable performance. The conductor surface is the only area of the conductor with 100% current density at all frequencies. The smoothness of the conductor surface is imperative because the surface is a guide rail for the entire energy envelope. The best copper and silver conductor metals have fewer grain boundaries and low oxygen content for low distortion and high performance.Perfect-Surface Copper has an astonishingly smooth and pure surface. Proprietary metal-processing technology protects the wire’s surface at every stage of drawing and fabrication. When high-purity low-oxide copper is kept as soft, pure and smooth as possible, it becomes a wonderfully low-distortion conductor. For over 30 years AudioQuest has pioneered the use of superior metals; yet even we were surprised by this huge leap in performance. PSC clearly outperforms previous AQ metals that cost over ten times as much. Electrical and magnetic interaction between strands in a conventional cable is the greatest source of distortion, often causing a somewhat dirty, harsh sound. Solid conductors are fundamental toward achieving Red Riverss very clean sound.Nitrogen-Injected Hard-Cell Foam Insulation :Insulation is necessary to keep the positive and negative conductors separate and to give stability to cable geometry. Insulation is also a dielectric because it is inside the conductors magnetic field. Dielectrics absorb energy, which after a delay is then released in the signal, causing smearing and distortion. Better insulation reduces distortion by absorbing less energy.Red River utilises Nitrogen-Injected Hard-Cell Foam insulation and is also used exclusively in most of AudioQuest’s video and digital audio cables. Similar to Foamed-PE, it is nitrogen-injected to create air pockets. ‘Hard’ foam is used because the stiffness of the material allows the conductors in the cable to maintain the same relationship with each other along the full length of the cable, thus ensuring that the characteristic impedance of the cable is consistent.Metal-Layer Noise-Dissipation System (NDS) :100% shield coverage is easy. Preventing captured RF Interference from modulating the equipment’s ground reference requires AQ’s Noise-Dissipation System. Noise-Dissipation System prevents a significant amount of RFI from reaching the equipment’s ground plane.AudioQuest’s Noise-Dissipation System (NDS) offers a compelling solution to this challenge by using metal-only or alternating layers of metal and carbon-loaded synthetics to effectively “shield the shield,” absorbing and reflecting the Radio Frequency (RF) energy before it reaches the layer attached to the ground.Red River ultilises the Metal-Layer Noise-Dissipation System (NDS) to prevent most RFI from reaching the equipment’s ground plane.Triple-Balanced Geometry :Geometry is the physical relationship of the conductors to one another within a cable and determines a cable’s most basic electrical values (capacitance and inductance). Different cable applications have different/specialized geometry requirements, and so these applications do not merely follow a ‘one size fits all’ approach. Better geometry leads to lower levels of distortion.The three conductors in “Triple-Balanced” Red River cables ensure that whether prepared with RCA or XLR plugs, the positive and negative signals have equally low-distortion conducting paths. The 100% coverage shield is never used as an inferior conductor.DirectionalityAudioQuest’s understanding of conductor directionality and its effect on audio performance has steadily evolved, growing stronger and more complete. All audio cables are directional. The correct direction is determined by the arrows on the plugs or cable parts.Cold-Welded Gold-Plated Plugs :AudioQuest specifies materials and designs each of its own connectors from the ground up, resulting in the long-lasting quality and exceptional performance you deserve. These components are crucial to the overall performance of a cable.To provide the best possible performance for each application, AudioQuest designs each of its connectors from the ground up. These components are crucial to the overall performance of the cable. Painstaking care is taken to evaluate the highest quality materials and design for every application.AudioQuest pays special attention to the plating it uses over its connectors’ carefully crafted base metals. Wherever possible, gold connectors are plated directly over the copper, with no destructive intermediate layer of nickel or alloy, while all silver-plated connectors are Direct-Silver plated.AudioQuest has incorporated Cold-Weld connection technology into most of their interconnects and all prepared speaker cables..Joining conductors to plugs requires every bit as much care and precision as any other aspect of cable manufacture. AudioQuests Cold-Weld System uses several tons of pressure to make a near-perfect connection that ensures that the structural integrity of the conductor and plug is kept completely intact, all without the damaging effect of heat. Cold-Welding avoids the introduction of heat and extra materials like solder, which change the character of the wire at the point of termination.This plug design allows for a connection devoid of solder, which is a common source of distortion. Because the ground shells are stamped instead of machined, the metal can be chosen for low distortion instead of machinability.Specification :Metal: Solid Long-Grain CopperGeometry: Triple Balanced (Separate Ground-Reference Conductor)Dielectric: Nitrogen-Injected Hard-Cell FoamNoise-Dissipation System: Metal-Layer NDSJacket Colour: Black/Red BraidTermination: Cold-Welded, Gold-PlatedTERMSPlease bid with confidence, the item is exactly as described. We are authorised dealers for all new items that we sell.Guarantees & Warranties: Brand New products are covered by their respective UK and European warranties, details of which are included with the product. Any Used / Repaired / B-Stock items are sold “As Seen” without warranty unless stated otherwise in the listingReturns:Most Buy It Now purchases are protected by the Distance Selling Regulations. To cancel a Contract, you must inform us in writing, and we will provide return instructions. You must return the products to us at your own cost and risk. You will not have any right to cancel a Contract for the supply of products that have been customised for you, such as pre-cut or terminated speaker cables. This provision does not affect your statutory rights. We cannot accept returns for Ex Display / Repaired / B-Stock or items sold by auction unless the item was not as described in the listing. The buyer must contact us within 3 days of receiving the item to initiate a return. The buyer is responsible for return shipping charges.Payment:We ask that payment is made within 3 days.Shipping:All goods purchased are securely and safely packaged for transit. The cost of Packaging materials (e.g. Jiffy Bags, Bubble Wrap etc) is included in the P&P charge. Items will normally be sent within 3 working days of receipt of cleared payment.Stock:Most items are either in stock with us or our suppliers and available for dispatch within 3 days. Occasionally, an item may be awaiting stock and in these instances we will contact you to confirm you are happy to wait for the item. If availability is key for you, we recommend you check an item is in stock before placing your order.Feedback:We always reciprocate feedback. Please contact us through the eBay system if there is a problem.Images:We often use library photos on our auctions for illustrative purposes only – we are not responsible for colour variances or style updates - you will receive the model and specification stated on the auction.All product serial numbers of items sold on eBay are logged for our mutual protection.Thank you for looking at our listing, please do not hesitate to contact us should you have any questions. Please contact us through the eBay system. Regrettably, we only sell within the UK at this time so do not ask us to ship to other destinations

New 1.5m AudioQuest Red River RCA Analogue Audio Interconnect 2 RCA to 2 RCAThis listing is for a New 1.5m AudioQuest Red River RCA Stereo Analogue Audio Interconnect 2 RCA to 2 RCA. Normally £229Red River’s solid Long-Grain Copper allows a smoother and clearer sound than cables using regular OFHC (Oxygen-Free High-Conductivity) copper.Solid Perfect-Surface Copper Conductors (PSC) :Strand interaction is the single greatest cause of distortion in a cable. Semi-Solid Concentric Packed Conductors avoid many strand-interaction distortion mechanisms. Solid-core conductors offer a complete and compelling solution to this problem.Conductor metal quality is critical for the best cable performance. The conductor surface is the only area of the conductor with 100% current density at all frequencies. The smoothness of the conductor surface is imperative because the surface is a guide rail for the entire energy envelope. The best copper and silver conductor metals have fewer grain boundaries and low oxygen content for low distortion and high performance.Perfect-Surface Copper has an astonishingly smooth and pure surface. Proprietary metal-processing technology protects the wire’s surface at every stage of drawing and fabrication. When high-purity low-oxide copper is kept as soft, pure and smooth as possible, it becomes a wonderfully low-distortion conductor. For over 30 years AudioQuest has pioneered the use of superior metals; yet even we were surprised by this huge leap in performance. PSC clearly outperforms previous AQ metals that cost over ten times as much. Electrical and magnetic interaction between strands in a conventional cable is the greatest source of distortion, often causing a somewhat dirty, harsh sound. Solid conductors are fundamental toward achieving Red Riverss very clean sound.Nitrogen-Injected Hard-Cell Foam Insulation :Insulation is necessary to keep the positive and negative conductors separate and to give stability to cable geometry. Insulation is also a dielectric because it is inside the conductors magnetic field. Dielectrics absorb energy, which after a delay is then released in the signal, causing smearing and distortion. Better insulation reduces distortion by absorbing less energy.Red River utilises Nitrogen-Injected Hard-Cell Foam insulation and is also used exclusively in most of AudioQuest’s video and digital audio cables. Similar to Foamed-PE, it is nitrogen-injected to create air pockets. ‘Hard’ foam is used because the stiffness of the material allows the conductors in the cable to maintain the same relationship with each other along the full length of the cable, thus ensuring that the characteristic impedance of the cable is consistent.Metal-Layer Noise-Dissipation System (NDS) :100% shield coverage is easy. Preventing captured RF Interference from modulating the equipment’s ground reference requires AQ’s Noise-Dissipation System. Noise-Dissipation System prevents a significant amount of RFI from reaching the equipment’s ground plane.AudioQuest’s Noise-Dissipation System (NDS) offers a compelling solution to this challenge by using metal-only or alternating layers of metal and carbon-loaded synthetics to effectively “shield the shield,” absorbing and reflecting the Radio Frequency (RF) energy before it reaches the layer attached to the ground.Red River ultilises the Metal-Layer Noise-Dissipation System (NDS) to prevent most RFI from reaching the equipment’s ground plane.Triple-Balanced Geometry :Geometry is the physical relationship of the conductors to one another within a cable and determines a cable’s most basic electrical values (capacitance and inductance). Different cable applications have different/specialized geometry requirements, and so these applications do not merely follow a ‘one size fits all’ approach. Better geometry leads to lower levels of distortion.The three conductors in “Triple-Balanced” Red River cables ensure that whether prepared with RCA or XLR plugs, the positive and negative signals have equally low-distortion conducting paths. The 100% coverage shield is never used as an inferior conductor.DirectionalityAudioQuest’s understanding of conductor directionality and its effect on audio performance has steadily evolved, growing stronger and more complete. All audio cables are directional. The correct direction is determined by the arrows on the plugs or cable parts.Cold-Welded Gold-Plated Plugs :AudioQuest specifies materials and designs each of its own connectors from the ground up, resulting in the long-lasting quality and exceptional performance you deserve. These components are crucial to the overall performance of a cable.To provide the best possible performance for each application, AudioQuest designs each of its connectors from the ground up. These components are crucial to the overall performance of the cable. Painstaking care is taken to evaluate the highest quality materials and design for every application.AudioQuest pays special attention to the plating it uses over its connectors’ carefully crafted base metals. Wherever possible, gold connectors are plated directly over the copper, with no destructive intermediate layer of nickel or alloy, while all silver-plated connectors are Direct-Silver plated.AudioQuest has incorporated Cold-Weld connection technology into most of their interconnects and all prepared speaker cables..Joining conductors to plugs requires every bit as much care and precision as any other aspect of cable manufacture. AudioQuests Cold-Weld System uses several tons of pressure to make a near-perfect connection that ensures that the structural integrity of the conductor and plug is kept completely intact, all without the damaging effect of heat. Cold-Welding avoids the introduction of heat and extra materials like solder, which change the character of the wire at the point of termination.This plug design allows for a connection devoid of solder, which is a common source of distortion. Because the ground shells are stamped instead of machined, the metal can be chosen for low distortion instead of machinability.Specification :Metal: Solid Long-Grain CopperGeometry: Triple Balanced (Separate Ground-Reference Conductor)Dielectric: Nitrogen-Injected Hard-Cell FoamNoise-Dissipation System: Metal-Layer NDSJacket Colour: Black/Red BraidTermination: Cold-Welded, Gold-PlatedTERMSPlease bid with confidence, the item is exactly as described. We are authorised dealers for all new items that we sell.Guarantees & Warranties: Brand New products are covered by their respective UK and European warranties, details of which are included with the product. Any Used / Repaired / B-Stock items are sold “As Seen” without warranty unless stated otherwise in the listingReturns:Most Buy It Now purchases are protected by the Distance Selling Regulations. To cancel a Contract, you must inform us in writing, and we will provide return instructions. You must return the products to us at your own cost and risk. You will not have any right to cancel a Contract for the supply of products that have been customised for you, such as pre-cut or terminated speaker cables. This provision does not affect your statutory rights. We cannot accept returns for Ex Display / Repaired / B-Stock or items sold by auction unless the item was not as described in the listing. The buyer must contact us within 3 days of receiving the item to initiate a return. The buyer is responsible for return shipping charges.Payment:We ask that payment is made within 3 days.Shipping:All goods purchased are securely and safely packaged for transit. The cost of Packaging materials (e.g. Jiffy Bags, Bubble Wrap etc) is included in the P&P charge. Items will normally be sent within 3 working days of receipt of cleared payment.Stock:Most items are either in stock with us or our suppliers and available for dispatch within 3 days. Occasionally, an item may be awaiting stock and in these instances we will contact you to confirm you are happy to wait for the item. If availability is key for you, we recommend you check an item is in stock before placing your order.Feedback:We always reciprocate feedback. Please contact us through the eBay system if there is a problem.Images:We often use library photos on our auctions for illustrative purposes only – we are not responsible for colour variances or style updates - you will receive the model and specification stated on the auction.All product serial numbers of items sold on eBay are logged for our mutual protection.Thank you for looking at our listing, please do not hesitate to contact us should you have any questions. Please contact us through the eBay system. Regrettably, we only sell within the UK at this time so do not ask us to ship to other destinations

AudioQuest Red River XLR Interconnect Cables - 1 Meter Pair - New - Open Box Authorized Dealer Since 1980 - Factory Warranty Applies Cable is New. Boxes are rough, torn or otherwise distressed. About Audioquest Factory Authorized Open Box Products: These items have been opened for one reason or another. Product Condition is “As-New” and includes the Audioquest warranty stated below. Most cable and accessory items have their original boxes and packaging. Sometimes boxes may be torn or show wear. Cables that dont have their boxes will come in a sealed plastic bag. Niagara series products will always have their original boxes, packaging and owners manual. Audioquest Product Warranty for the United States:AudioQuest products are manufactured to exacting standards and are subject to rigorous quality control.However, if a manufacturing defect is found in any cable, connector, or factory assembled product, AudioQuest’s non-transferable original-owner limited lifetime warranty has you covered for any cable, connector, or factory assembled product purchased through an authorized AudioQuest US dealer.At its option, AudioQuest will repair or replace any defective cable, connector, or factory assembled product that has not been abused, for the lifetime of the product. Proof of original purchase is required.For all other products, AudioQuest provides a limited, non-transferable, one-year warranty to original owners who purchased their product through an authorized AudioQuest dealer in the United States. At its option, AudioQuest will repair or replace any defective product that has not been abused, for up to one year from the original date of purchase. Proof of original purchase is required.Cables not terminated by AudioQuest that require service may be returned to AudioQuest with prior authorization and repaired for a fee.This warranty is not an upgrade program for AudioQuest HDMI cables that were designed to meet previous generations of HDMI specifications. Current AudioQuest models are designed to meet HDMI 2.0 (18Gbps) or HDMI 2.1 (48Gbps).All generations of HDMI cable will provide some, but not all, of the features made possible by HDMI 2.0 and 2.1. All generations of HDMI cable are backwards compatible—they provide all the capabilities of previous generations.To experience the audio/video benefits made possible by the latest HDMI 2.1 hardware, an HDMI cable must meet HDMI specifications, specifically an FRL-enabled bandwidth of 48Gbps.This warranty is valid in the United States only. For warranty policies in other countries, please contact your local dealer or distributor.Limitations and ConditionsThis warranty is subject to the following limitations and conditions:The unit will not be covered under the warranty if:• It has been altered or modified in any way.• It has been damaged due to misuse,negligence,accident or improper operation.• It has been subjected to water damage, or extremes of humidity or temperature.• It has been purchased from an unauthorized dealer, or unauthorized repair or service has beenperformed. For repairs and returns:• A request for a Return Merchandise Authorization (RMA) number must be made in writing or via phone to AudioQuest.• A return address and phone number must be included.• Returned product must be accompanied by the RMA number, a written description of the defect orissue, and a photocopy of the original purchase receipt.• Customer is responsible for paying shipping charges to AudioQuest.• If the product is found to be out of warranty, as in the conditions specified above, the customer will begiven the option to pay for the repairs or replacement, or to have the unit returned to them.Limited to original purchaser:• This Warranty is for the sole benefit of the original purchaser and shall not be transferred to a subsequent purchaser of the product. Warranty Outside the USA, Netherlands, Germany or the UKAudioQuest has authorized distributors in many countries of the world. In each country, the authorized distributor or dealer thereof has accepted the responsibility for warranty of products sold in their respective countries. Warranty service should normally be obtained from the authorized distributor or dealer from whom you purchased your product. In the unlikely event of service required beyond the capability of the distributor, AudioQuest will fulfill the conditions of the warranty. Such product must be returned at the owner’s expense to AudioQuest, together with a photocopy of the bill of sale for that product, a detailed description of the problem, and any information necessary for return shipment.AudioQuest makes no other express warranty of any kind whatsoever. All implied warranties, including warranties of merchantability and fitness for a particular purpose, exceeding the specific provisions of this warranty are hereby disclaimed and excluded from this warranty.No representative or other person is authorized to assume for AudioQuest any liability except as stated in this warranty. ©2022 AudioQuest

Heute biete ich Ihnen folgendes an: 2 X Audioquest Red River XLR Referenzkabel KABEL / 2 Meter / technischer Zustand: guter Zustand optischer Zustand: guter Zustand Falls Sie den oben aufgeführten Artikel ersteigern und diesen persönlich bei mir abholen, so können wir diesen sehr gerne gemeinsam auf den von mir angegebenen Zustand hin überprüfen. No shipping to USA

Audioquest Red River XLR custom assembled by Audioquest, 8 meter or 26’ 3”. With box, as new. Equipment repositioning necessitates sale. Any questions answered. 2 cables.

Audioquest Red River XLR - XLR 1 Meter Length - Excellent Condition. 1x Pair (Left and Right) of Audioquest Red River XLR cables in 1 meter length. In the excellent condition with original box and packing. Fully “burnt in” as was used between my pre amp and mono blocks for the last couple of years. Will be sent recorded, tracked delivery. Collection also welcome. UK buyers only please. No returns. Full details from the manufacturer: Specification : Metal: Solid Long-Grain Copper Geometry: Triple Balanced (Separate Ground-Reference Conductor) Dielectric: Nitrogen-Injected Hard-Cell Foam Noise-Dissipation System: Metal-Layer NDS Jacket Colour: Black/Red Braid Termination: Cold-Welded, Gold-Plated Audioquest Red River 2 XLR to 2 XLR Audio Cable North America has two Red Rivers, North and South. Red River South has been home to many peoples; it once was the border between the US and colonial Spain, and today forms part of the border between the rival states of Texas and Oklahoma. Red River North forms in a confluence of rivers in North Dakota and Minnesota, but its history is Canada’s. The Red River North’s early settlers were the Métis, whose ancestry was French and aboriginal Canadian. The Métis in 1869 began an uprising known as the Red River Rebellion, which challenged the Canadian government, eventually leading to the formation of the province of Manitoba. Solid Perfect-Surface Copper Conductors (PSC) : Strand interaction is the single greatest cause of distortion in a cable. Semi-Solid Concentric Packed Conductors avoid many strand-interaction distortion mechanisms. Solid-core conductors offer a complete and compelling solution to this problem. Conductor metal quality is critical for the best cable performance. The conductor surface is the only area of the conductor with 100% current density at all frequencies. The smoothness of the conductor surface is imperative because the surface is a guide rail for the entire energy envelope. The best copper and silver conductor metals have fewer grain boundaries and low oxygen content for low distortion and high performance. Perfect-Surface Copper has an astonishingly smooth and pure surface. Proprietary metal-processing technology protects the wire’s surface at every stage of drawing and fabrication. When high-purity low-oxide copper is kept as soft, pure and smooth as possible, it becomes a wonderfully low-distortion conductor. For over 30 years AudioQuest has pioneered the use of superior metals; yet even we were surprised by this huge leap in performance. PSC clearly outperforms previous AQ metals that cost over ten times as much. Electrical and magnetic interaction between strands in a conventional cable is the greatest source of distortion, often causing a somewhat dirty, harsh sound. Solid conductors are fundamental toward achieving Red River's very clean sound. Nitrogen-Injected Hard-Cell Foam Insulation : Insulation is necessary to keep the positive and negative conductors separate and to give stability to cable geometry. Insulation is also a dielectric because it is inside the conductor's magnetic field. Dielectrics absorb energy, which after a delay is then released in the signal, causing smearing and distortion. Better insulation reduces distortion by absorbing less energy. Red River uses Nitrogen-Injected Hard-Cell Foam insulation and is used exclusively in most of AudioQuest’s video and digital audio cables. Similar to Foamed-PE, it is nitrogen-injected to create air pockets. ‘Hard’ foam is used because the stiffness of the material allows the conductors in the cable to maintain the same relationship with each other along the full length of the cable, thus ensuring that the characteristic impedance of the cable is consistent. Metal-Layer Noise-Dissipation System (NDS) : 100% shield coverage is easy. Preventing captured RF Interference from modulating the equipment’s ground reference requires AQ’s Noise-Dissipation System. Noise-Dissipation System prevents a significant amount of RFI from reaching the equipment’s ground plane. AudioQuest’s Noise-Dissipation System (NDS) offers a compelling solution to this challenge by using metal-only or alternating layers of metal and carbon-loaded synthetics to effectively “shield the shield,” absorbing and reflecting the Radio Frequency (RF) energy before it reaches the layer attached to the ground. Red River ultilises the Metal-Layer Noise-Dissipation System (NDS) to prevent most RFI from reaching the equipment’s ground plane. Triple-Balanced Geometry : Geometry is the physical relationship of the conductors to one another within a cable and determines a cable’s most basic electrical values (capacitance and inductance). Different cable applications have different/specialized geometry requirements, and so these applications do not merely follow a ‘one size fits all’ approach. Better geometry leads to lower levels of distortion. The three conductors in “Triple-Balanced” Red River cables ensure that whether prepared with RCA or XLR plugs, the positive and negative signals have equally low-distortion conducting paths. The 100% coverage shield is never used as an inferior conductor. Directionality AudioQuest’s understanding of conductor directionality and its effect on audio performance has steadily evolved, growing stronger and more complete. All audio cables are directional. The correct direction is determined by the arrows on the plugs or cable parts. Cold-Welded Gold-Plated Plugs : AudioQuest specifies materials and designs each of its own connectors from the ground up, resulting in the long-lasting quality and exceptional performance you deserve. These components are crucial to the overall performance of a cable. To provide the best possible performance for each application, AudioQuest designs each of its connectors from the ground up. These components are crucial to the overall performance of the cable. Painstaking care is taken to evaluate the highest quality materials and design for every application. AudioQuest pays special attention to the plating it uses over its connectors’ carefully crafted base metals. Wherever possible, gold connectors are plated directly over the copper, with no destructive intermediate layer of nickel or alloy, while all silver-plated connectors are Direct-Silver plated. AudioQuest has incorporated Cold-Weld connection technology into most of their interconnects and all prepared speaker cables.. Joining conductors to plugs requires every bit as much care and precision as any other aspect of cable manufacture. AudioQuest's Cold-Weld System uses several tons of pressure to make a near-perfect connection that ensures that the structural integrity of the conductor and plug is kept completely intact, all without the damaging effect of heat. Cold-Welding avoids the introduction of heat and extra materials like solder, which change the character of the wire at the point of termination. This plug design allows for a connection devoid of solder, which is a common source of distortion. Because the ground shells are stamped instead of machined, the metal can be chosen for low distortion instead of machinability.

Audioquest Red River XLR custom assembled by Audioquest, 8 meter or 26’ 3”. With box, as new. Equipment repositioning necessitates sale. Any questions answered. 2 cables.

AudioQuest Red River Interconnect Cables - 2 Meter Pair - RCA Termination Authorized Dealer Since 1980 - Factory Warranty Applies Cable is New. Boxes are rough, torn or otherwise distressed. Retail Price $269.95 About AudioQuest Factory Authorized Open Box Products: These items have been opened for one reason or another. Product Condition is “As-New” and includes the Audioquest warranty stated below. Most cable and accessory items have their original boxes and packaging. Sometimes boxes may be torn or show wear. Cables that dont have their boxes will come in a sealed plastic bag. Niagara series products will always have their original boxes, packaging and owners manual. AudioQuest Product Warranty for the United States: AudioQuest products are manufactured to exacting standards and are subject to rigorous quality control.However, if a manufacturing defect is found in any cable, connector, or factory assembled product, AudioQuest’s non-transferable original-owner limited lifetime warranty has you covered for any cable, connector, or factory assembled product purchased through an authorized AudioQuest US dealer.At its option, AudioQuest will repair or replace any defective cable, connector, or factory assembled product that has not been abused, for the lifetime of the product. Proof of original purchase is required.For all other products, AudioQuest provides a limited, non-transferable, one-year warranty to original owners who purchased their product through an authorized AudioQuest dealer in the United States. At its option, AudioQuest will repair or replace any defective product that has not been abused, for up to one year from the original date of purchase. Proof of original purchase is required.Cables not terminated by AudioQuest that require service may be returned to AudioQuest with prior authorization and repaired for a fee.This warranty is not an upgrade program for AudioQuest HDMI cables that were designed to meet previous generations of HDMI specifications. Current AudioQuest models are designed to meet HDMI 2.0 (18Gbps) or HDMI 2.1 (48Gbps).All generations of HDMI cable will provide some, but not all, of the features made possible by HDMI 2.0 and 2.1. All generations of HDMI cable are backwards compatible—they provide all the capabilities of previous generations.To experience the audio/video benefits made possible by the latest HDMI 2.1 hardware, an HDMI cable must meet HDMI specifications, specifically an FRL-enabled bandwidth of 48Gbps.This warranty is valid in the United States only. For warranty policies in other countries, please contact your local dealer or distributor.Limitations and ConditionsThis warranty is subject to the following limitations and conditions:The unit will not be covered under the warranty if:• It has been altered or modified in any way.• It has been damaged due to misuse,negligence,accident or improper operation.• It has been subjected to water damage, or extremes of humidity or temperature.• It has been purchased from an unauthorized dealer, or unauthorized repair or service has beenperformed. For repairs and returns:• A request for a Return Merchandise Authorization (RMA) number must be made in writing or via phone to AudioQuest.• A return address and phone number must be included.• Returned product must be accompanied by the RMA number, a written description of the defect orissue, and a photocopy of the original purchase receipt.• Customer is responsible for paying shipping charges to AudioQuest.• If the product is found to be out of warranty, as in the conditions specified above, the customer will begiven the option to pay for the repairs or replacement, or to have the unit returned to them.Limited to original purchaser:• This Warranty is for the sole benefit of the original purchaser and shall not be transferred to a subsequent purchaser of the product. Warranty Outside the USA, Netherlands, Germany or the UKAudioQuest has authorized distributors in many countries of the world. In each country, the authorized distributor or dealer thereof has accepted the responsibility for warranty of products sold in their respective countries. Warranty service should normally be obtained from the authorized distributor or dealer from whom you purchased your product. In the unlikely event of service required beyond the capability of the distributor, AudioQuest will fulfill the conditions of the warranty. Such product must be returned at the owner’s expense to AudioQuest, together with a photocopy of the bill of sale for that product, a detailed description of the problem, and any information necessary for return shipment.AudioQuest makes no other express warranty of any kind whatsoever. All implied warranties, including warranties of merchantability and fitness for a particular purpose, exceeding the specific provisions of this warranty are hereby disclaimed and excluded from this warranty.No representative or other person is authorized to assume for AudioQuest any liability except as stated in this warranty. ©2022 AudioQuest

Excellent condition. Was used briefly between a McIntosh MVP901 Blu-ray and a McIntosh MX121. Sold the 901 and this is no longer needed.

AudioQuest Red River Interconnect Cables - 1.5 Meter Pair - RCA Termination Retail Price $249.95 Authorized Dealer Since 1980 - Factory Warranty Applies Cable is New. Boxes are rough, torn or otherwise distressed. About AudioQuest Factory Authorized Open Box Products: These items have been opened for one reason or another. Product Condition is “As-New” and includes the Audioquest warranty stated below. Most cable and accessory items have their original boxes and packaging. Sometimes boxes may be torn or show wear. Cables that dont have their boxes will come in a sealed plastic bag. Niagara series products will always have their original boxes, packaging and owners manual. AudioQuest Product Warranty for the United States: AudioQuest products are manufactured to exacting standards and are subject to rigorous quality control.However, if a manufacturing defect is found in any cable, connector, or factory assembled product, AudioQuest’s non-transferable original-owner limited lifetime warranty has you covered for any cable, connector, or factory assembled product purchased through an authorized AudioQuest US dealer.At its option, AudioQuest will repair or replace any defective cable, connector, or factory assembled product that has not been abused, for the lifetime of the product. Proof of original purchase is required.For all other products, AudioQuest provides a limited, non-transferable, one-year warranty to original owners who purchased their product through an authorized AudioQuest dealer in the United States. At its option, AudioQuest will repair or replace any defective product that has not been abused, for up to one year from the original date of purchase. Proof of original purchase is required.Cables not terminated by AudioQuest that require service may be returned to AudioQuest with prior authorization and repaired for a fee.This warranty is not an upgrade program for AudioQuest HDMI cables that were designed to meet previous generations of HDMI specifications. Current AudioQuest models are designed to meet HDMI 2.0 (18Gbps) or HDMI 2.1 (48Gbps).All generations of HDMI cable will provide some, but not all, of the features made possible by HDMI 2.0 and 2.1. All generations of HDMI cable are backwards compatible—they provide all the capabilities of previous generations.To experience the audio/video benefits made possible by the latest HDMI 2.1 hardware, an HDMI cable must meet HDMI specifications, specifically an FRL-enabled bandwidth of 48Gbps.This warranty is valid in the United States only. For warranty policies in other countries, please contact your local dealer or distributor.Limitations and ConditionsThis warranty is subject to the following limitations and conditions:The unit will not be covered under the warranty if:• It has been altered or modified in any way.• It has been damaged due to misuse,negligence,accident or improper operation.• It has been subjected to water damage, or extremes of humidity or temperature.• It has been purchased from an unauthorized dealer, or unauthorized repair or service has beenperformed. For repairs and returns:• A request for a Return Merchandise Authorization (RMA) number must be made in writing or via phone to AudioQuest.• A return address and phone number must be included.• Returned product must be accompanied by the RMA number, a written description of the defect orissue, and a photocopy of the original purchase receipt.• Customer is responsible for paying shipping charges to AudioQuest.• If the product is found to be out of warranty, as in the conditions specified above, the customer will begiven the option to pay for the repairs or replacement, or to have the unit returned to them.Limited to original purchaser:• This Warranty is for the sole benefit of the original purchaser and shall not be transferred to a subsequent purchaser of the product. Warranty Outside the USA, Netherlands, Germany or the UKAudioQuest has authorized distributors in many countries of the world. In each country, the authorized distributor or dealer thereof has accepted the responsibility for warranty of products sold in their respective countries. Warranty service should normally be obtained from the authorized distributor or dealer from whom you purchased your product. In the unlikely event of service required beyond the capability of the distributor, AudioQuest will fulfill the conditions of the warranty. Such product must be returned at the owner’s expense to AudioQuest, together with a photocopy of the bill of sale for that product, a detailed description of the problem, and any information necessary for return shipment.AudioQuest makes no other express warranty of any kind whatsoever. All implied warranties, including warranties of merchantability and fitness for a particular purpose, exceeding the specific provisions of this warranty are hereby disclaimed and excluded from this warranty.No representative or other person is authorized to assume for AudioQuest any liability except as stated in this warranty. ©2022 AudioQuest

AUDIOQUEST RED RIVER COPPIA CAVI XLR NUOVI. Acquistati ma non utilizzati e sostituiti con analogo modello di lunghezza maggiore in quanto la taglia 0,5m non mi era sufficiente per il collegamento. Costruzione di eccezionale qualità meccanica ed acustica. Connettori e pins dorati, la lunghezza 0,5m è perfetta per collegare apparati hi-end sovrapposti o vicini, più è corto il cavo meno sono le perdite introdotte. Spedizione gratuita in Italia,

DescriptionAuthenticity: 100% AUTHENTIC! If you have any question about the condition, accessories, or anything about the product,Please feel free to message us. We are glad to answer all your concerns. ShippingDHL, Fedex Fastshipping3-10 business days after shipment(Tracking number + Insurance.)PaymentPlease give me the payment within 3days from the date of bid.About UsWe sell our items on other websites and in our retail stores in Japan at the same time.If the item was sold out before your purchase, your order will be cancelled and a full refund will be issued immediately. International Buyers - Please Note:Import duties, taxes, and charges are not included in the item price or shipping cost. These charges are the buyers responsibility. Please check with your countrys customs office to determine what these additional costs will be prior to bidding or buying.We do not mark merchandise values below value or mark items as - gifts - The US and International government regulations prohibit such behavior. Thank you.

AUDIOQUEST RED RIVER COPPIA CAVI XLR NUOVI. Acquistati ma non utilizzati e sostituiti con analogo modello di lunghezza maggiore in quanto la taglia 0,5m non mi era sufficiente per il collegamento. Costruzione di eccezionale qualità meccanica ed acustica. Connettori e pins dorati, la lunghezza 0,5m è perfetta per collegare apparati hi-end sovrapposti o vicini, più è corto il cavo meno sono le perdite introdotte. Spedizione gratuita in Italia,

AUDIOQUEST RED RIVER COPPIA CAVI XLR NUOVI. Acquistati ma non utilizzati e sostituiti con analogo modello di lunghezza maggiore in quanto la taglia 0,5m non mi era sufficiente per il collegamento. Costruzione di eccezionale qualità meccanica ed acustica. Connettori e pins dorati, la lunghezza 0,5m è perfetta per collegare apparati hi-end sovrapposti o vicini, più è corto il cavo meno sono le perdite introdotte. Spedizione gratuita in Italia,

AudioQuest Red River Male XLR to Female XLR Single Cable - 4.92 ft. (1.5m). Single Red River XLR cable in 1.5M length. Purchased from local authorized dealer and in excellent condition.

AUDIOQUEST RED RIVER COPPIA CAVI XLR NUOVI. Acquistati ma non utilizzati e sostituiti con analogo modello di lunghezza maggiore in quanto la taglia 0,5m non mi era sufficiente per il collegamento. Costruzione di eccezionale qualità meccanica ed acustica. Connettori e pins dorati, la lunghezza 0,5m è perfetta per collegare apparati hi-end sovrapposti o vicini, più è corto il cavo meno sono le perdite introdotte. Spedizione gratuita in Italia,

Audioquest Red River Xlr 4m.1 pair.

AudioQuest Red River Interconnect Cables - 1.5 Meter Pair - RCA Termination Authorized Dealer Since 1980 - Factory Warranty Applies Cable is New. Boxes are rough, torn or otherwise distressed. About AudioQuest Factory Authorized Open Box Products: These items have been opened for one reason or another. Product Condition is “As-New” and includes the Audioquest warranty stated below. Most cable and accessory items have their original boxes and packaging. Sometimes boxes may be torn or show wear. Cables that dont have their boxes will come in a sealed plastic bag. Niagara series products will always have their original boxes, packaging and owners manual. AudioQuest Product Warranty for the United States: AudioQuest products are manufactured to exacting standards and are subject to rigorous quality control.However, if a manufacturing defect is found in any cable, connector, or factory assembled product, AudioQuest’s non-transferable original-owner limited lifetime warranty has you covered for any cable, connector, or factory assembled product purchased through an authorized AudioQuest US dealer.At its option, AudioQuest will repair or replace any defective cable, connector, or factory assembled product that has not been abused, for the lifetime of the product. Proof of original purchase is required.For all other products, AudioQuest provides a limited, non-transferable, one-year warranty to original owners who purchased their product through an authorized AudioQuest dealer in the United States. At its option, AudioQuest will repair or replace any defective product that has not been abused, for up to one year from the original date of purchase. Proof of original purchase is required.Cables not terminated by AudioQuest that require service may be returned to AudioQuest with prior authorization and repaired for a fee.This warranty is not an upgrade program for AudioQuest HDMI cables that were designed to meet previous generations of HDMI specifications. Current AudioQuest models are designed to meet HDMI 2.0 (18Gbps) or HDMI 2.1 (48Gbps).All generations of HDMI cable will provide some, but not all, of the features made possible by HDMI 2.0 and 2.1. All generations of HDMI cable are backwards compatible—they provide all the capabilities of previous generations.To experience the audio/video benefits made possible by the latest HDMI 2.1 hardware, an HDMI cable must meet HDMI specifications, specifically an FRL-enabled bandwidth of 48Gbps.This warranty is valid in the United States only. For warranty policies in other countries, please contact your local dealer or distributor.Limitations and ConditionsThis warranty is subject to the following limitations and conditions:The unit will not be covered under the warranty if:• It has been altered or modified in any way.• It has been damaged due to misuse,negligence,accident or improper operation.• It has been subjected to water damage, or extremes of humidity or temperature.• It has been purchased from an unauthorized dealer, or unauthorized repair or service has beenperformed. For repairs and returns:• A request for a Return Merchandise Authorization (RMA) number must be made in writing or via phone to AudioQuest.• A return address and phone number must be included.• Returned product must be accompanied by the RMA number, a written description of the defect orissue, and a photocopy of the original purchase receipt.• Customer is responsible for paying shipping charges to AudioQuest.• If the product is found to be out of warranty, as in the conditions specified above, the customer will begiven the option to pay for the repairs or replacement, or to have the unit returned to them.Limited to original purchaser:• This Warranty is for the sole benefit of the original purchaser and shall not be transferred to a subsequent purchaser of the product. Warranty Outside the USA, Netherlands, Germany or the UKAudioQuest has authorized distributors in many countries of the world. In each country, the authorized distributor or dealer thereof has accepted the responsibility for warranty of products sold in their respective countries. Warranty service should normally be obtained from the authorized distributor or dealer from whom you purchased your product. In the unlikely event of service required beyond the capability of the distributor, AudioQuest will fulfill the conditions of the warranty. Such product must be returned at the owner’s expense to AudioQuest, together with a photocopy of the bill of sale for that product, a detailed description of the problem, and any information necessary for return shipment.AudioQuest makes no other express warranty of any kind whatsoever. All implied warranties, including warranties of merchantability and fitness for a particular purpose, exceeding the specific provisions of this warranty are hereby disclaimed and excluded from this warranty.No representative or other person is authorized to assume for AudioQuest any liability except as stated in this warranty. ©2022 AudioQuest

AUDIOQUEST RED RIVER COPPIA CAVI XLR NUOVI. Acquistati ma non utilizzati e sostituiti con analogo modello di lunghezza maggiore in quanto la taglia 0,5m non mi era sufficiente per il collegamento. Costruzione di eccezionale qualità meccanica ed acustica. Connettori e pins dorati, la lunghezza 0,5m è perfetta per collegare apparati hi-end sovrapposti o vicini, più è corto il cavo meno sono le perdite introdotte. Spedizione gratuita in Italia,