ARCAM FMJ P7 MULTI CHANNEL POWER AMPThe ARCAM P7 Multichannel Power Amplifier will deliver equally breathtaking results from both music and home cinema sources. It will enthrall even the most experienced and discerning listener.Construction/Design is Class AB amplifier with first 50W in class AA completely modular design, with 7 identical and fully isolated power amplifiers, these may be daisy chained for bi-amping or tri-amping suitable loudspeakers. Each amplifier module has its own bridge rectifiers and 20,000 micrfarads of storage capacitance, fed from a total of 14 individual windings on the p7s two massive 1500va toroidal power transformers. This arrangement ensures near perfect isolation between the channels for the avoidance of hum loops. It also means that each channel can always deliver its full rated continuous output power of 150 Watts into 8 ohms or 230 Watts into 4 ohms, irrespective of what the other channels are doing. The advanced current feedback circuit topology used in the p7 is a further development of that used in Arcams award-winning a85 and a32 amplifiers and has ultra low distortion together with exceptional dynamic range and transient response.The p7 is a thx specified, 7 channel power amplifier which has been designed to deliver reference standard amplification in high performance audio-video installations. It is the perfect partner to the av8 processor, but will also complement the performance of any other high-quality preamp processor. As well as being technically superb, great attention has been paid to the aesthetic design of the p7 to ensure it will look stunning in your home installation. The p7 represents a tour-de-force in amplifier design. Certain to enrich your listening experience, its abundant power and finesse firmly positions Arcam in a small, select group of world-class producers.As the p7 amplifier is capable of delivering over 1.6 kilowatts of continuous undistorted audio power, there were a number of engineering challenges that have had to be overcome to ensure both short and long-term reliable operation. Each channel uses four Sanken heavy duty bipolar output transistors firmly bolted to a large custom designed aluminium heatsink. These heatsinks are thermally very efficient so that, under normal conditions, the amplifier needs only convection cooling and is thus silent in use. With so much power on tap the p7 is equipped with a heavy duty mains cable and socket, coupled to a microprocessor controlled softstart sequencer which, to minimise mains inrush currents, turns on the channels one by one. This system is powered from its own small toroidal power transformer, permitting the p7 to be remotely switched in and out of standby via a 12-volt trigger input.The microprocessor continuously monitors the condition of each channel, including temperature, output current and dc offset, to ensure correct operation or instant shut-down under fault conditions. It also controls a variable-speed cooling fan, for those rare occasions when convection cooling is not enough. The p7 features a beautifully contoured front panel and integral air intake slot, with 7 multicoloured LEDs to show the operating status of each channel. The whole case is made of heavy gauge aluminium, which helps the overall sound quality due to its excellent thermal and non-magnetic properties. Because it weighs over 30 kg, even the p7s feet are made from machined aluminium, complete with easy slide plastic inserts to help with installation.PICK UP ONLY OR I WILL DELIVER IF NOT TO FAR AWAY £15 GREATER MANCHESTER AREA, MESSAGE ME FOR DELIVERYOUTSIDE OF MANCHESTER AND IF WE CAN COME TO AGREEMENT I WILL DELIVER, DELIVERY COST PAID UPFRONT VIAPAYPAL.THX certified Multi-Channel power amplifierDelivers a massive 150W per channel into 8 Ohms 230W per channel into 4 ohmsNear perfect channel isolation prevents signal distortionCan be daisy chained for Bi or even Tri-ampingMulti-coloured LED display12V trigger for remote activationWith high grade power cordAll working as it should

ARCAM FMJ P7 MULTI CHANNEL POWER AMPThe ARCAM P7 Multichannel Power Amplifier will deliver equally breathtaking results from both music and home cinema sources. It will enthrall even the most experienced and discerning listener.Construction/Design is Class AB amplifier with first 50W in class AA completely modular design, with 7 identical and fully isolated power amplifiers, these may be daisy chained for bi-amping or tri-amping suitable loudspeakers. Each amplifier module has its own bridge rectifiers and 20,000 micrfarads of storage capacitance, fed from a total of 14 individual windings on the p7s two massive 1500va toroidal power transformers. This arrangement ensures near perfect isolation between the channels for the avoidance of hum loops. It also means that each channel can always deliver its full rated continuous output power of 150 Watts into 8 ohms or 230 Watts into 4 ohms, irrespective of what the other channels are doing. The advanced current feedback circuit topology used in the p7 is a further development of that used in Arcams award-winning a85 and a32 amplifiers and has ultra low distortion together with exceptional dynamic range and transient response.The p7 is a thx specified, 7 channel power amplifier which has been designed to deliver reference standard amplification in high performance audio-video installations. It is the perfect partner to the av8 processor, but will also complement the performance of any other high-quality preamp processor. As well as being technically superb, great attention has been paid to the aesthetic design of the p7 to ensure it will look stunning in your home installation. The p7 represents a tour-de-force in amplifier design. Certain to enrich your listening experience, its abundant power and finesse firmly positions Arcam in a small, select group of world-class producers.As the p7 amplifier is capable of delivering over 1.6 kilowatts of continuous undistorted audio power, there were a number of engineering challenges that have had to be overcome to ensure both short and long-term reliable operation. Each channel uses four Sanken heavy duty bipolar output transistors firmly bolted to a large custom designed aluminium heatsink. These heatsinks are thermally very efficient so that, under normal conditions, the amplifier needs only convection cooling and is thus silent in use. With so much power on tap the p7 is equipped with a heavy duty mains cable and socket, coupled to a microprocessor controlled softstart sequencer which, to minimise mains inrush currents, turns on the channels one by one. This system is powered from its own small toroidal power transformer, permitting the p7 to be remotely switched in and out of standby via a 12-volt trigger input.The microprocessor continuously monitors the condition of each channel, including temperature, output current and dc offset, to ensure correct operation or instant shut-down under fault conditions. It also controls a variable-speed cooling fan, for those rare occasions when convection cooling is not enough. The p7 features a beautifully contoured front panel and integral air intake slot, with 7 multicoloured LEDs to show the operating status of each channel. The whole case is made of heavy gauge aluminium, which helps the overall sound quality due to its excellent thermal and non-magnetic properties. Because it weighs over 30 kg, even the p7s feet are made from machined aluminium, complete with easy slide plastic inserts to help with installation.PICK UP ONLY OR I WILL DELIVER IF NOT TO FAR AWAY £15 GREATER MANCHESTER AREA, MESSAGE ME FOR DELIVERYOUTSIDE OF MANCHESTER AND IF WE CAN COME TO AGREEMENT I WILL DELIVER, DELIVERY COST PAID UPFRONT VIAPAYPAL.THX certified Multi-Channel power amplifierDelivers a massive 150W per channel into 8 Ohms 230W per channel into 4 ohmsNear perfect channel isolation prevents signal distortionCan be daisy chained for Bi or even Tri-ampingMulti-coloured LED display12V trigger for remote activationWith high grade power cordAll working as it should

Arcam Alpha 7R Stereo Integrated Amplifier 230V AP7X13185 50 60 mhz 400va max I dont know much about this as part of a stack system I inherited selling other parts separately with power supply and wires tested and working

ARCAM FMJ P7 7 CHANNEL POWER AMPLIFIER WORKING GOOD CONDITION 150 WPC ON ALL 7CH.

Power Lead Supplied NO REMOTE Condition - Tested and checked fully and found to be in great working order with only cosmetic wears A few knocks and marks / scratches as shown in photos Does not affect the high standard of this unit Item is used so you should expect signs of use and age throughout, such as scratches, marks, dust and fading - anything major or more noticeable will be stated here and shown in the pictures - please do study them well. I have experience with sending delicate items so rest assured the item will be securely and adequately packaged to ensure a safe shipping process. I ship domestically and worldwide via the eBay global shipping program (GSP) When buying from outside of the UK, Please be aware your purchase may be subject to Tax and/or Import charges. Collection also welcome Thank you

ARCAM FMJ P7 MULTI 7 CHANNEL POWER AMPThe ARCAM P7 Multichannel Power Amplifier will deliver equally breathtaking results from both music and home cinema sources. It will enthrall even the most experienced and discerning listener.Construction/Design is Class AB amplifier with first 50W in class AA completely modular design, with 7 identical and fully isolated power amplifiers, these may be daisy chained for bi-amping or tri-amping suitable loudspeakers. Each amplifier module has its own bridge rectifiers and 20,000 micrfarads of storage capacitance, fed from a total of 14 individual windings on the p7s two massive 1500va toroidal power transformers. This arrangement ensures near perfect isolation between the channels for the avoidance of hum loops. It also means that each channel can always deliver its full rated continuous output power of 150 Watts into 8 ohms or 230 Watts into 4 ohms, irrespective of what the other channels are doing. The advanced current feedback circuit topology used in the p7 is a further development of that used in Arcams award-winning a85 and a32 amplifiers and has ultra low distortion together with exceptional dynamic range and transient response.The p7 is a thx specified, 7 channel power amplifier which has been designed to deliver reference standard amplification in high performance audio-video installations. It is the perfect partner to the av8 processor, but will also complement the performance of any other high-quality preamp processor. As well as being technically superb, great attention has been paid to the aesthetic design of the p7 to ensure it will look stunning in your home installation. The p7 represents a tour-de-force in amplifier design. Certain to enrich your listening experience, its abundant power and finesse firmly positions Arcam in a small, select group of world-class producers.As the p7 amplifier is capable of delivering over 1.6 kilowatts of continuous undistorted audio power, there were a number of engineering challenges that have had to be overcome to ensure both short and long-term reliable operation. Each channel uses four Sanken heavy duty bipolar output transistors firmly bolted to a large custom designed aluminium heatsink. These heatsinks are thermally very efficient so that, under normal conditions, the amplifier needs only convection cooling and is thus silent in use. With so much power on tap the p7 is equipped with a heavy duty mains cable and socket, coupled to a microprocessor controlled softstart sequencer which, to minimise mains inrush currents, turns on the channels one by one. This system is powered from its own small toroidal power transformer, permitting the p7 to be remotely switched in and out of standby via a 12-volt trigger input.The microprocessor continuously monitors the condition of each channel, including temperature, output current and dc offset, to ensure correct operation or instant shut-down under fault conditions. It also controls a variable-speed cooling fan, for those rare occasions when convection cooling is not enough. The p7 features a beautifully contoured front panel and integral air intake slot, with 7 multicoloured LEDs to show the operating status of each channel. The whole case is made of heavy gauge aluminium, which helps the overall sound quality due to its excellent thermal and non-magnetic properties. Because it weighs over 30 kg, even the p7s feet are made from machined aluminium, complete with easy slide plastic inserts to help with installation.This is very heavy and post is expensive so pick up only or i will deliver in greater manchester for £20.If you are further away please contact me for negotiated delivery price before auction ends, but i am not delivering if to far away.DELIVERY PAID UPFRONT BEFORE DELIVERY VIA PAYPAL. THE REST CASH ON DELIVERY. CASH ON COLLECTION IS OKTHX certified Multi-Channel power amplifierDelivers a massive 150W per channel into 8 Ohms 230W per channel into 4 ohmsNear perfect channel isolation prevents signal distortionCan be daisy chained for Bi or even Tri-ampingMulti-coloured LED display12V trigger for remote activationWith high grade power cord

ARCAM FMJ P7 MULTI 7 CHANNEL POWER AMPThe ARCAM P7 Multichannel Power Amplifier will deliver equally breathtaking results from both music and home cinema sources. It will enthrall even the most experienced and discerning listener.Construction/Design is Class AB amplifier with first 50W in class AA completely modular design, with 7 identical and fully isolated power amplifiers, these may be daisy chained for bi-amping or tri-amping suitable loudspeakers. Each amplifier module has its own bridge rectifiers and 20,000 micrfarads of storage capacitance, fed from a total of 14 individual windings on the p7s two massive 1500va toroidal power transformers. This arrangement ensures near perfect isolation between the channels for the avoidance of hum loops. It also means that each channel can always deliver its full rated continuous output power of 150 Watts into 8 ohms or 230 Watts into 4 ohms, irrespective of what the other channels are doing. The advanced current feedback circuit topology used in the p7 is a further development of that used in Arcams award-winning a85 and a32 amplifiers and has ultra low distortion together with exceptional dynamic range and transient response.The p7 is a thx specified, 7 channel power amplifier which has been designed to deliver reference standard amplification in high performance audio-video installations. It is the perfect partner to the av8 processor, but will also complement the performance of any other high-quality preamp processor. As well as being technically superb, great attention has been paid to the aesthetic design of the p7 to ensure it will look stunning in your home installation. The p7 represents a tour-de-force in amplifier design. Certain to enrich your listening experience, its abundant power and finesse firmly positions Arcam in a small, select group of world-class producers.As the p7 amplifier is capable of delivering over 1.6 kilowatts of continuous undistorted audio power, there were a number of engineering challenges that have had to be overcome to ensure both short and long-term reliable operation. Each channel uses four Sanken heavy duty bipolar output transistors firmly bolted to a large custom designed aluminium heatsink. These heatsinks are thermally very efficient so that, under normal conditions, the amplifier needs only convection cooling and is thus silent in use. With so much power on tap the p7 is equipped with a heavy duty mains cable and socket, coupled to a microprocessor controlled softstart sequencer which, to minimise mains inrush currents, turns on the channels one by one. This system is powered from its own small toroidal power transformer, permitting the p7 to be remotely switched in and out of standby via a 12-volt trigger input.The microprocessor continuously monitors the condition of each channel, including temperature, output current and dc offset, to ensure correct operation or instant shut-down under fault conditions. It also controls a variable-speed cooling fan, for those rare occasions when convection cooling is not enough. The p7 features a beautifully contoured front panel and integral air intake slot, with 7 multicoloured LEDs to show the operating status of each channel. The whole case is made of heavy gauge aluminium, which helps the overall sound quality due to its excellent thermal and non-magnetic properties. Because it weighs over 30 kg, even the p7s feet are made from machined aluminium, complete with easy slide plastic inserts to help with installation.This is very heavy and post is expensive so pick up only or i will deliver in greater manchester for £20.If you are further away please contact me for negotiated delivery price before auction ends, but i am not delivering if to far away.DELIVERY PAID UPFRONT BEFORE DELIVERY VIA PAYPAL. THE REST CASH ON DELIVERY. CASH ON COLLECTION IS OKTHX certified Multi-Channel power amplifierDelivers a massive 150W per channel into 8 Ohms 230W per channel into 4 ohmsNear perfect channel isolation prevents signal distortionCan be daisy chained for Bi or even Tri-ampingMulti-coloured LED display12V trigger for remote activationWith high grade power cord

Arcam P7 Power Amplifier 7 channel power amp 7x150wpc. I have found the power cable and this amp works perfectly all 7 channels sound fine. The only issue it has is one if the loudspeaker terminals is cracked and loose, it still works fine . It’s in decent condition with just some marks. One shallow dent in the top rear left hand side. Please see pictures for condition. Postage is expensive at £45.00 It weights 35 kilos in its box.

Arcam P75 Power Amplifier. Full working order, only two marks of note, see last 2 photos in the listing.

ARCAM FMJ P7 MULTI CHANNEL POWER AMPThe ARCAM P7 Multichannel Power Amplifier will deliver equally breathtaking results from both music and home cinema sources. It will enthrall even the most experienced and discerning listener.Construction/Design is Class AB amplifier with first 50W in class AA completely modular design, with 7 identical and fully isolated power amplifiers, these may be daisy chained for bi-amping or tri-amping suitable loudspeakers. Each amplifier module has its own bridge rectifiers and 20,000 micrfarads of storage capacitance, fed from a total of 14 individual windings on the p7s two massive 1500va toroidal power transformers. This arrangement ensures near perfect isolation between the channels for the avoidance of hum loops. It also means that each channel can always deliver its full rated continuous output power of 150 Watts into 8 ohms or 230 Watts into 4 ohms, irrespective of what the other channels are doing. The advanced current feedback circuit topology used in the p7 is a further development of that used in Arcams award-winning a85 and a32 amplifiers and has ultra low distortion together with exceptional dynamic range and transient response.The p7 is a thx specified, 7 channel power amplifier which has been designed to deliver reference standard amplification in high performance audio-video installations. It is the perfect partner to the av8 processor, but will also complement the performance of any other high-quality preamp processor. As well as being technically superb, great attention has been paid to the aesthetic design of the p7 to ensure it will look stunning in your home installation. The p7 represents a tour-de-force in amplifier design. Certain to enrich your listening experience, its abundant power and finesse firmly positions Arcam in a small, select group of world-class producers.As the p7 amplifier is capable of delivering over 1.6 kilowatts of continuous undistorted audio power, there were a number of engineering challenges that have had to be overcome to ensure both short and long-term reliable operation. Each channel uses four Sanken heavy duty bipolar output transistors firmly bolted to a large custom designed aluminium heatsink. These heatsinks are thermally very efficient so that, under normal conditions, the amplifier needs only convection cooling and is thus silent in use. With so much power on tap the p7 is equipped with a heavy duty mains cable and socket, coupled to a microprocessor controlled softstart sequencer which, to minimise mains inrush currents, turns on the channels one by one. This system is powered from its own small toroidal power transformer, permitting the p7 to be remotely switched in and out of standby via a 12-volt trigger input.The microprocessor continuously monitors the condition of each channel, including temperature, output current and dc offset, to ensure correct operation or instant shut-down under fault conditions. It also controls a variable-speed cooling fan, for those rare occasions when convection cooling is not enough. The p7 features a beautifully contoured front panel and integral air intake slot, with 7 multicoloured LEDs to show the operating status of each channel. The whole case is made of heavy gauge aluminium, which helps the overall sound quality due to its excellent thermal and non-magnetic properties. Because it weighs over 30 kg, even the p7s feet are made from machined aluminium, complete with easy slide plastic inserts to help with installation.THX certified Multi-Channel power amplifierDelivers a massive 150W per channel into 8 Ohms 230W per channel into 4 ohmsNear perfect channel isolation prevents signal distortionCan be daisy chained for Bi or even Tri-ampingMulti-coloured LED display12V trigger for remote activationWith high grade power cord