PIONEER ARM REST . Aftermarket . High Quality Aluminum Bezel with a set screw . So you can adjust the tone arm . The way it should be . This is a PL-55X Polished aluminum pole Bezel .So the set screw (Flat blade Screwdriver 5/64) is in the rear of the Bezel . You must pre-adjust the height . Prior to final mounting of the rest . See pictures . Once you have the desired height . Turntable Arm Rest for the500 Series . Hand Machined . Tone arm rest . Adjustable Jaw . For:PL-518 PL-518XPL-514PL-516PL-513 PL-540 Nylon locking clasp . Formed fitting Stainless steel RodPolished Aluminum Bezel. Washer and 10mm (Head) nut .Set screw German stainless steel . Works better than the original and is very strong ! Please see pics . Thanks ...

PIONEER PL-518 HGT DIRECT DRIVE TURNTABLE OPERATING INSTRUCTIONS This is an original Pioneer instruction leaflet for the PL-518 turntable. It includes assembley & setting up methods as well as operating instructions. The leaflet comprises 8 pages of about 8½” x 11” (22x28cm) which are intact although worn. The leaflet can be sent worldwide. Please enquire if your country is not shown.Carriage will be combined whenever possible. FMy items are auction only. Bids can be made at any time before the auction ends.

Pioneer PL-518 Hinge Backing Plates. So, somebody gave me a nice PL-518 Stereo Turntable. Had the cover and the hinges, but no backing plates. So I looked at them on Ebay and decided to make my own. So I did. Not perfect, but they work as you can see in the second picture. I used a 4 hole setup because I think 4 holes will be stronger and put minimal stress on the plate itself, although the hinge springs are not that strong. These should snap right on your hinges. You can then put the cover on, and measure them for fit. About an 1/8 in gap between the top of the table. Use a pencil. Use a small drill bit to create a starter hole. Small wood screws should work fine. I believe these will fit other 500 series turntables as well. These were made on a filament 3D printer. I am retired and love to tinker.

PIONEER PL-518 HGT DIRECT DRIVE TURNTABLE OPERATING INSTRUCTIONS This is an original Pioneer instruction leaflet for the PL-518 turntable. It includes assembley & setting up methods as well as operating instructions. The leaflet comprises 8 pages of about 8½” x 11” (22x28cm) which are intact although worn. The leaflet can be sent worldwide. Please enquire if your country is not shown.Carriage will be combined whenever possible. FMy items are auction only. Bids can be made at any time before the auction ends.

pioneer PL-518 direct drive turntable.

please take a look at other pioneer parts I have listed Pioneer Turntable Hinge Brackets for PL-514 PL-516 PL-518 also fits PL-512 in excellent condition

Pioneer PL-518 Hinge Backing Plates. So, somebody gave me a nice PL-518 Stereo Turntable. Had the cover and the hinges, but no backing plates. So I looked at them on Ebay and decided to make my own. So I did. Not perfect, but they work as you can see in the second picture. I used a 4 hole setup because I think 4 holes will be stronger and put minimal stress on the plate itself, although the hinge springs are not that strong. These should snap right on your hinges. You can then put the cover on, and measure them for fit. About an 1/8 in gap between the top of the table. Use a pencil. Use a small drill bit to create a starter hole. Small wood screws should work fine. I believe these will fit other 500 series turntables as well. These were made on a filament 3D printer. I am retired and love to tinker.

Pioneer PL-518 Turntable Parting Screws